20 Most Recent Frigidaire ATF6000ES Front Load Washer - Page 8 Questions & Answers

Just need to remove like you are pulling a tire off of a rim. it is held on by pressure from its self and a tension spring.

you'll need to call a repair professional and have the electronics controller assembly replaced.

Hello friend, thank you for the post!

I understand that your Frigidaire washer, ATF6000ES, continues to cycle after your wash is complete. Sounds like it could possibly be an issue with your control panel or sensor either one may not be communicating that the wash cycles have been completed. Since it maybe either one of these underlying issues, I would recommend having a technician come out to the home to diagnose and repair your washer. I hope this is helpful. -Matt

Hello friend, thank you for the post!

I understand that your Frigidaire washer, ATF6000es, keeps pausing during a cycle. Generally that means there is a disruption in the cycle. I would try resetting your appliance, unplug the power cord or flip the household circuit breaker, for ten minutes. If that does not resolve the issue it could be a problem with your control board or wiring harness within the washer. I would recommend having a technician come out to the home to diagnose and repair the appliance. Hope this is helpful. -Matt

Hello Friend, this is Z. I appreciate your post! I understand your Frigidaire washer is showing error code E20. First, check the drain hose for any restrictions or kinks. If you have check the hose and it appears to be clear and free, then potentially the underlying issue may be the main control board or pump. Generally it is a good idea to have a professional take a look at it to get to the root cause. Cost of parts and technical expertise entailed in these types of replacements can be a bit tricky.

Hello Friend, this is Z. Thank you for your post! If you are receiving an error code E11, please check the following:

·Is the incoming water flow normal? If it is, does the fill water continue to enter your washer? If yes, disconnect power from your washing machine. Did the water fill stop? If so, a service technician may need to check the pressure sensor or switch to determine if it needs replacement. ·If your water flow is abnormal, double-check water faucets to ensure they are in the "on" position. If on, your incoming water pressure may be above 30 PSI and could need adjusting. Check for any kinked or blocked water hoses or clogged water screens. If you've cleared the water screen and/or unblocked any kinked water hoses, and the problem still persists, it could possibly be a water inlet valve assembly. ·If you have checked all of the above, your washer may need a main control board replacement. I would recommend contacting a qualified service technician to further assist you in diagnosing this issue. Hope this helps!

Is the water supply on? Is it blocked by something? Has the hose been trapped and blocked?

U posted this under fridgidaire fl washer btw

Remove clamp around it

Um what is logik

Hi Friend, this is Z. Thank you for your post! Based on the symptoms you are describing, please confirm that the house valves are fully turned on. Otherwise, typically, faulty switch does not allow the valve inside to turn or a kinked fill hose. Other possibilities of more potential serious issues are water valve faults, faulty control board, pressure switch or wiring failure. If I was in your position, I will personally consult a professional to move forward accurately and assist with the repairs.

Hi Friend, this is Z. Thank you for your post! I see that your question is listed under Frigidaire washer, ATF6000ES. To unlock the controls, press Options and Select at the same time and hold roughly 15 seconds until "LOC" is no longer displayed. I hope this helps!

Hi Friend, this is Z. Thank you for your question! Typically error code E5E indicates that your Frigidaire washer is experiencing a communication problem. Base on the intensity of the issue, I suggest contacting a professional technician to accurately repair your washer. Typically, a technician will need to check the wiring between the main control board and the speed control board. Depending on the diagnoses and if the wiring is bad, it has to be corrected. However if the wiring is good the main control board may need to be replace or if the problem is not corrected, the speed control board is possibly faulty.

lay the drain hose on the floor and if the water runs out then the system and pump is free.

Good Afternoon Friend, I understand that the liquid softener dispenser does not empty on your Frigidaire washer, model# ATF6000ES. Please try resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and try any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful. -Best Regards- WP

not knowing what this code means I would call the number listed on your paperwork or the machine..

Good Afternoon Marleen, I understand the control panel on your Frigidaire washer, model# ATF6000ES, keeps lighting up. I also see that you have to keep hitting the cancel button and are wondering if it is a safety issue. I wouldn't think it would be a safety issue. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful. -Best Regards- WP

Good Afternoon Friend, I understand you want to know how to reassemble the drain pump filter for your Frigidaire washer, model# ATF6700FS0. Typically, this is not a do it yourself job, as there are no step by step instruction manuals. I suggest contacting your local authorized technician for further assistance. They have been trained on your appliance and should be able to reassemble the drain pump filter with ease. Hope this is helpful. -Best Regards- WP

Hi Friend, this is Z. I am happy to assist you! If you are getting an error code E21, it usually means that your washer is not pumping out water fast enough. First, check the drain hose for any restrictions or kinks. If you have check the hose and it appears to be clear and free, then potentially the underlying issue may be the main control board or pump. Generally it is a good idea to have a professional take a look at it to get to the root cause. Cost of parts and technical expertise entailed in these types of replacements can be a bit tricky. Best regards!

Error code 41 is about the door not latching. Appliancepartspros.com has the parts you need. Just enter your model #.