LG WM2277H Front Load Washer - Page 8 - Answered Questions & Fixed issues

It sounds as if the inner water seal has failed and allowed water to get into the bearings.. Rust on the bearings means they are no longer smooth..Hence the noise! Replacing the bearings (and possibly the shaft) is a big job. This is not an unusual problem with front lad washers. Too much detergent will shorten the life of the seal/bearings...Get quotes...Nomess

You can get the manual on the link below. Just scrool down and type in the # code then click on download now.

http://www.retrevo.com/search/v2/jsp/mytrevo/myTrevo.jsp?page=man


Good Luck and please rate 4 thumbs up for the free answer.

Hi,
LE code stands for locked motor error. When this error code appears in your front load washer it indicates a fault in the motor unit.
1 . Check the connections to the Coil/Stator at the rear of the unit possibly it should be something like a broken wire.

2 . Coil/Stator Assembly will be defective preventing the drive to operate.You should go for a replacement of that assembly.

Thank you !!

Access the water pump and look for plugged drain hoses or a plugged filter as well as a slipping impeller on the pump shaft--or even a dead pump motor. Spin usually will not occur if there is a high water level in the machine. Try draining the tub into a bucket, then see if it will go into spin mode. Hope this helps!

You might be using too much detergent and causing a sudslock condition. The machine uses very little water and any amount over a teaspoon of HE will simply cause the machine to lock down. An OE error means it took longer than 10 minutes to drain the tub. IF the machine is trying to correct a sud problem it will continually toss in more water till sudslock is corrected. Press and hold: SPIN SPEED & SOIL LEVEL buttons--then press POWER button.
Wait for door to lock.

Press the START button (6) times--this will fill the tub with hot water to the maximum setting when it stops filling.

Press the START button two more times--this will enable the tub to tumble.
After 3 hours--turn "off" the washer.
Turn the washer back "on".
Select the shortest wash cycle (usually "quick wash") and press "START". This will rinse out the tub.
This method of "TUB CLEAN" is *not* from a service manual but has been the best method for cleaning out LG washers more than a year into incorrect detergent usage. If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

I would definitely not attempt this if you have no experience. Is is quite a lengthy process. Specialised tools are required. Discontinue using immediatly, as it will cause further damage to machine and property.

Hi,
I think the hose which is connected from the tray box to the drum will be damaged kindly check it and replace it if there is no problem with that hose then check the outlet hose which connects the drum and drain out valve change the hose possibly

DIRECTIONS If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

this means the machine has tried to empty for 10 minutes check the filter and unblock it or else the drain hose is kinked or crushed, worse case scenerio is that you need a new water pump

Hi,
Here is a tip that will help you with that..

http://www.fixya.com/support/r4348161-lg_washing_machine_le_error_code_or

heatman101

YOU NEED THE CONTROL BOARD.
http://www.searspartsdirect.com/partsdirect/index.action

A final solution is to cut away the rear of the dispenser and allow the water to flow freely int the machine...

send me your email and ill send a manuel to you
[email protected]

le means your hall sensor on motor is faulty. if u r confident change sensor.or phone service companys 4 price on hall sensor replacement, or reply back 4 more help

LE = Load Error. It can be caused by an overly unbalanced load, or unusually heavy load, like wet pillows, coats, rugs, etc. Additional causes could be too much soap (caused by drag of suds between the inner to the outer tub) or it could be a failure of the Hall sensor.

Hello,
Here are the common error codes for the LG machines.

LG Washing Machine Error or Fault Codes

If you have a LG Washing Machine you may see an error code come up and wonder what it is. Here are the common error or fault codes that will be displayed on the LG machine.

OE

This means that the washer has tried for ten minutes to drain the water out of your machine and the water did not drain out.

UE

This means that the load in the drum is out of balance causing excessive vibration when spinning.

IE

This means that the washer has not filled with water in 8 minutes.

LE

This means that the motor and the control panel are not talking to each other properly

PF

Power Failure – The power has gone out to the machine and then has come back on

FE

This means that there is too much water in the machine

PE

This means that the water level sensor is not working properly

CE

The washer motor has received and over current condition

TE

This means that your heating sensor is not working properly

SE

This means that you had a temporary sensor error

HE

This means that you had a temporary heater problem

DHE

This means that you had a temporary dry heater problem

This will give you a basic idea of what has caused your error code.


Heatman101

If it does it with no clothes in then :


Drum Loose, Suspension leg shot

Inner drum out of shape

It is mounted right on the heating element and both come as an assembly, See page 41 of the MANUAL If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

you can purchase a "hammer arrestor" from any major hardware store and have it installed which should cure your problem.

Unplug remove the back. Loosen large bolt in center of rotor. Slide rotor off of spline. Look at the stator with the windings. At the bottom of the stator where the harness plugs in is the hall sensor. Remove the 10 mm bolts holding the stator on and don't let it drop. Un plug the plug and snap the hall sensor off and snap the new one on. Re assemble.