LG WM2688H Front Load Washer - Page 5 - Answered Questions & Fixed issues


If you wish to get some details; check the site linked here. Pull up older posts........

http://electro-medical.blogspot.com/

LG WM Washing... | Answered on Jun 12, 2016 | 55 views


take the back off

see if the water pump making that noise or is broken

should look something like this one
26197828-pe3l0ypp1vfpknq0mkt0qwu4-3-0.jpg

LG WM Washing... | Answered on May 18, 2016 | 94 views


run a wire thru it no doubt it is plugged with crud

LG WM Washing... | Answered on May 02, 2016 | 168 views


There probably isn't one. If you are certain power is getting to the machine, there may have been control failure.

LG WM Washing... | Answered on Apr 25, 2016 | 95 views


2 possible causes
the water solenoid control valve is split in the diaphragm and not stopping the water
the small hose from the base of the tub to the level control pressure unit is split or disconnected or the pressure unit has failed and is not activating the water control valve

LG WM Washing... | Answered on Mar 25, 2016 | 156 views


Take out the soap drawer and clean the fabric softner compartment. This happens when there is residues left. And it gets clogged up.

LG WM Washing... | Answered on Feb 17, 2016 | 124 views


The obvious question is how do you know that it is soap? What washing machine is it? The biggest problem with most washing machines is that people use too much soap to begin with. I would go to a store and get a new t-shirt or something. Run the machine with nothing in it. Then put the shirt in and run it again without adding any soap. When it is done check the shirt for soap. There could be a build up on the inside of the drum.

LG WM Washing... | Answered on Feb 13, 2016 | 126 views


Please do not do another load of wash until this problem is fixed, or you may find yourself with a house/apartment fire!
I am thinking your motor (most likely) or the controls (least) have a short, and are causing your problem.
Oh, yes.
Take a really good look at the circuit breaker box inside, because a broken or loose ground wire ( there are two) can also cause this problem.
One ground wire should be white, one should be bare.
Each should be securely screwed into the lugs of the grounded section of the circuit breaker box.
God bless your efforts.

LG WM Washing... | Answered on Jan 12, 2016 | 75 views


pull back the lip and look for a wire and spring that goes around the gasket. check out repair videos on repairclinic.com or appliancepartspros.com.

LG WM Washing... | Answered on Jan 10, 2016 | 71 views


more often than not, this is a problem with a faulty heater in the machine not getting it up to temperatre (which help the powder dissolve). Put it on a 90 degree wash and keep checking the temperature, if it's not getting hot, then you need to swap out the heater. Ift IS getting hot, then it could be an empty pump problem. If the pump or waste pipe are blocked, the wash will take a very long time but it will be struggling to evacuate water and add fresh, which will also causse powder residue to be left behind. But I'd put my money on a heater fault

LG WM Washing... | Answered on Dec 26, 2015 | 115 views


something is blocking the pump.unplug first.take drain hose and hold down at floor level with a container to catch water.it may be a coin or a wire from a bra,hair bobble etc feel in the pump to see if the impeller is free to move.if it is then suspect something in the hose between drum and pump like a sock.that restricts flow enough to put up fault code

LG WM Washing... | Answered on Nov 18, 2015 | 94 views


machine needs to be level.so it cant rock side to side or front to back adj feet .when u load machine put half in and rotate drum half turn and put the rest of load in.that should balance load.dont overload.try running empty if it still showing ua

LG WM Washing... | Answered on Nov 18, 2015 | 181 views


why do you use tub clean function, we have never had the need to reclean the tub having just run hot detergent and water thru it .

LG WM Washing... | Answered on Oct 11, 2015 | 153 views


Hi Elaine258, you may need to take a look into it from the top, the soap, softener dispenser may be catching. Fairly straight forward to do, disconnect from the mains, two fasteners at the back hold the top on (if I remember right) lift top up from back and push forward, vvwalla.
Hope this helps.

LG WM Washing... | Answered on Oct 04, 2015 | 1,089 views


Hi Declan.....need to know which model machine you have.

LG WM Washing... | Answered on Jul 23, 2015 | 87 views


actually I never heard of a TUB CLEAN cycle .contact the MFG and tech support

LG WM Washing... | Answered on Jul 17, 2015 | 119 views


open door and see if the drum can be moved up and down or side to side a lot. if it can, then you need a new bearing most likely. this would most likely only happen on a older washer that has been used quite a bit. repairclinic.com and appliancepartspros.com both have very good videos to show how the bearing can be replaced. takes some time and work, but if everything else on the washer is good, it could be worth the trouble. good luck.

LG WM Washing... | Answered on Jul 11, 2015 | 430 views


YOU NEED TO REPLACE THE THERMISTER.

LG WM Washing... | Answered on Jun 03, 2015 | 86 views

Not finding what you are looking for?
LG WM2688H Front Load Washer Logo

150 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...