That is the problem with top loaders, central agitators and long items like towels, They get tangled and tear. It is also likely that your towels are worn out.
To wash successfully, you need a lot of water and only 3 or 4 towels.
Front loaders don't do that and uses a tenth of the water and energy to heat that water.
https://www.lg.com > ... > Washing Machines
7 cubic feet and ultra-large at 4. 3 - you can fit more into every load - saving time and energy. Slamproof™ Lid: With a top-load LG washing machine, you' ...
Matching Dryer: DLE2050W
Weight: 190 lbs
Capacity Facet: 4.0
Energy Star Compliant: Energy Star
Rating: 4.6 · 351 reviews
..
It will be fine. The transit bolts are there to protect the springs and dampers from stretching if the machine is tilted or laid on its back during shipping to the seller and delivery to the home.
In use with the transit bolts removed it allow the springs, the shock absorber and the big concrete block to absorb movement as the spin evens out the balance of the clothes with the first part of the spin. It also stops the machine walking across the floor as all of the movement is transferred to to case and feet.
It will be fine, I have done it myself after I moved from one house to another and then didn't do any washing for a week or two.
Enjoy your new machine. Finally, just for fun
If the gear system of your LG direct drive washing machine is broken even after you have replaced it and checked the clutch regulate motor, there could be a few other reasons why this is happening. Here are some possible solutions to try:
Check the motor: If the gear system is still not working, it could be a problem with the motor. Check if the motor is functioning properly and if it is getting power.
Check the control board: The control board could also be a potential issue. Check if the control board is functioning properly and if any of the connections are loose or damaged.
Check the drum bearings: The drum bearings may be worn out, causing the gear system to malfunction. Check if the drum bearings are in good condition or if they need to be replaced.
Check the pulley: The pulley may be worn out or damaged, causing the gear system to malfunction. Check if the pulley is in good condition and if it is properly aligned.
If none of these solutions work, it may be a more serious issue with the washing machine that requires professional repair. In that case, you may need to contact LG customer support or a qualified technician for assistance.
The E2 error code on an LG washing machine usually indicates a problem with the water supply. Here are some steps you can try to resolve the issue:
Check the water supply: Make sure that the water supply to the washing machine is turned on and the water pressure is adequate. If there is a problem with the water supply, fix it and try running the machine again.
Check the water inlet valve: The water inlet valve is responsible for controlling the water flow into the washing machine. If the valve is faulty, it can cause the E2 error code. To check the valve, unplug the machine and turn off the water supply. Remove the hoses from the valve and check if there is any debris or damage. If the valve is damaged, it will need to be replaced.
Check the water level sensor: The water level sensor is responsible for detecting the water level in the washing machine. If it is faulty, it can cause the E2 error code. To check the sensor, unplug the machine and locate the water level sensor. Check for any damage or debris and clean it. If the sensor is damaged, it will need to be replaced.
If the above steps do not resolve the issue, you may need to contact a professional for further assistance.
If you're experiencing an error on your LG front loader M80490CL washing machine, here are some steps you can try to clear the error:
Power off the washing machine by unplugging it or turning off the circuit breaker that powers it.
Wait for a few minutes to let the washing machine cool down.
Press and hold the "Start/Pause" button for about five seconds.
While still holding the "Start/Pause" button, turn on the washing machine by either plugging it back in or turning the circuit breaker back on.
Release the "Start/Pause" button once the washing machine begins to beep and the display shows "CL" to indicate that the error has been cleared.
If the error persists, refer to the troubleshooting section of the washing machine's user manual or contact LG customer support for further assistance.
This seems to be a very strange "Assessment". There is nothing on or inside a front loader washing machine that contains Oil. The motor is also tucked inside the machine often where it is difficult to get to. There will be small amounts of grease on the drum and motor bearings but not enough to affect other machine parts. I would suggest you get a second opinion from another good repairer.
LG will claim that this damage was not due to a part failing so it will not be covered by a warranty or guarantee. This will be see as damage being done 'on purpose' so it's not their problem.
It sounds like there may be an issue with your LG washing machine. The "err" sign and lack of additional information make it difficult to determine the exact problem. Some possible causes could be a clogged drain, a malfunctioning water inlet valve, or a problem with the machine's control board. It's best to consult the user manual or contact LG customer service for further assistance in troubleshooting the issue.
The "PF" error code on an LG washing machine typically indicates a power failure. This can be caused by a power outage, a tripped circuit breaker, or a problem with the electrical outlet or wiring.
Check the drain hose position if you hear the water go to the drain. If the drain hose is positioned too deeply in your sink or stand pipe, you create a siphon that pulls the water out of the tub. Make sure that the end of the hose is above the highest water level in the washer tub. If the water is inside the washer cabinet, check for a damaged seal (washer) between the tub and the drain hose. (On some machines, there is a tub and an inner basket. The point where the spin motor connects to the basket has a bearing in addition to the seal. Both must be replaced. This is not easy and isn't generally worth the cost if the machine is out of warranty.)
Please add a comment with the model number of the washer (usually found on the rim of the tub), if you would like me to try and find the parts diagram for the LG washer.
Cindy Wells
Examine the gearbox; it can be the cause of the issue.
Examine it for damage, such as stripped gears or worn-out bearings, and repair it if required.
Examine the clutch assembly: The clutch assembly engages and disengages the transmission and drive motor.
Check to see if the clutch assembly is in good condition and not worn out.
Examine the drive belt: The drive belt turns the drum and links the motor to the transmission.
Verify that the drive belt is not slack, worn out, or damaged.
Check the tub bearings: The washer's drum is supported by the tub bearings.
The gear system may malfunction if the tub bearings are worn out.
Contact the manufacturer: If none of the above solutions work, it may be necessary to contact the manufacturer for further assistance. They can provide more detailed troubleshooting steps or recommend a service professional to diagnose the problem.
Load the items you want to soak into the washer drum.
Press the "Power" button to turn on the washer.
Press the "Pre Wash" button, this will start a pre-wash cycle that will last for 5 minutes, this will give you the time to add any detergent or laundry pre-treatment solution.
Press the "Start/Pause" button to start the pre-wash cycle.
Press the "Delay Start" button to set the time you want the washer to start the main cycle. This will give you the opportunity to soak the clothes overnight
Press the "Start/Pause" button again to start the main cycle after the pre-wash cycle is complete.
Leave the items in the washer overnight.
In the morning, press the "Start/Pause" button to start the main cycle again.
When the cycle is complete, unload the items from the washer and dry them as usual.
There are a few potential reasons why your LG Roboking robotic vacuum cleaner might be spinning:
Obstacle detection: The Roboking is equipped with sensors that detect obstacles in its path, and when it encounters something it cannot navigate around, it may spin in place.
Stuck on a cord or rug: The robotic vacuum cleaner may be stuck on a cord or rug and spinning in place as it tries to free itself.
Mechanical problem: The vacuum cleaner may have a mechanical problem such as a stuck wheel or other issue that is preventing it from moving forward.
Low battery: If the battery is low, the Roboking may spin in place to indicate that it needs to be recharged.
Software or firmware bug: The software or firmware of the roboking may have a bug that causes the vacuum cleaner to spin.
It's best to check if there's any obstacle or cord that is stuck to the roboking, if there's not, it might be a good idea to contact the manufacturer for assistance or have a professional technician to check it.
You can also check the software version and see if there's an update available.
There are a few other potential causes for slow water flow in a washing machine:
Clogged or partially clogged water inlet valve: The water inlet valve is responsible for controlling the flow of water into the washing machine. If it is clogged or partially clogged, it can cause a reduction in water flow.
Washing machine pump: The pump is responsible for moving water through the washing machine. If it is damaged or not functioning properly, it can cause a reduction in water flow.
Water supply hose: The hose that supplies water to the washing machine may be clogged or damaged, which could cause a reduction in water flow.
The washing machine itself: There could be an issue with the internal components of the washing machine that is causing the slow water flow.
If you have checked the filters, water pressure, and solenoid and they are all functioning properly, you may want to try checking the water inlet valve, pump, water supply hose, and the washing machine itself for any issues that could be causing the slow water flow.
