20 Most Recent LG TROMM WM2688H 4.0 cu.ft. Front Loading SteamWasher - Page 6 Questions & Answers

please ask your question in english-you could use google translator-cheers Denny

mi lavadora da error fe

"FE" means (no surprise here) "Overflow error. The water is automatically pumped out because there has been an overflow.

Since this condition clearly demonstrates that the water level sensor is working fine and doing its job, the very likely culprit is the water inlet valve. You may be locky and find that of you take the valve out, there is an ovstruction in it (sometimes a bit of grit gets trapped in the valve holding it open. More likely, the valve is failing and not shutting once it has opened. You may then need to replace it.

IE = inlet error. Washer has not detected enough water after 8 minute fill time. Check screen at inlet water valves where hoses connect to machine for blockage. Look for kinked hose(s). Make sure there is water supply reaching machine. If all OK, most likely next thing is the water valve itself.

All of the ways to solve this problem are right on--take the filter out (in front on the bottom left when facing the machine). Before you do, take time to drain out the water with the hose below. Once drained open the filter and clean out. Try on speed wash with no spin. Nine minutes in you will know if the drain works. If not, turn on side and remove the washer pump. To do this, remove the hoses first starting with clamps. Then remove the three screws in front where the filter is. It easily comes out. The top pump is the drain pump. First mark the wires--blue is positive and black is negative. Remove the pump and clean out.The pump comes out of the casing. Try removing this and cleaning. If you have a power source, test the pump. If works, put back and start in fast cycle with no spin. If not, then you have to replace the drain pump. You will not find anyone in town the has the pump unless you live in New York or Dallas Texas. To get the pump at a reasonable price and expedited call and order through Sears at 18004881222. These guys are good and well get it to you as promised. The entire job once recieved the pump took about 30 minutes. Also, saved about $100 in labor. Good luck and hope this helps...

Posted by Jay on Jan 11 2009

I have the same washer now for several years now. I keep getting the smell now and then. After reading all these disappointed people I went down to the machine and cleaned out the "Pump filter". It had been smelling today, I was tired of this problem also. So i opened the little door at the bottom front left corner. There you find a little black hose, pull it out a little and pull the plug. There you drain the water that's laying inside smelling up the house. Now you un-screw the big black cap. Once you remove the cap, you find a plastic filter-catcher. I found paper, a dime, and several other things that came out of my pockets. You can take the basket to the sink and wash it out. Put it back together and try checking it in one month. Also I used some needle nose pliers to clean the nasty stuff around the gasket. At the bottom of gasket try pulling it back to get to the hair and ****. We have a dog, so the hair is bad.

Hello, and thank you for your question. I have links for troubleshooting, a link to manuals, ordering parts as needed, and scheduling service if needed. I hope this is helpful. http://bit.ly/zkfnZdhttp://bit.ly/112Lu7qhttp://bit.ly/yLv4Z5

You have an uneven load... ( not kidding here).. If you remove and/or reposition the clothes inside . and restart.. does it spin up and complete the cycle? ( probably yes).. but if no.. please elaborate on what it does or doesn't do so we can help.. I've experienced the same problem when my daughter tries to do her entire weeks worth ( maybe longer) of clothes in one load.. The quick fix is usually to down size the amount being washed.. Hope this helps you...

I shouldn't even respond to this if you have had 5 or 6 tech look at it because I don't want a Thanks for Trying, but it sounds like you are at the end of your rope. The pump motor should not have anything to do with the problem. If you did not have anything in the tub, including suds, doing the QC test, and you have checked and replaced all you have said, the only thing left is the main PCB part number 6871ER1078T