20 Most Recent Zebra Z4Mplus Label Printer - Page 4 Questions & Answers


shivacando: You can use the "zebra universal driver", the "zebra designer driver" from Zebra Technologies and also the "seagull driver" from Seagull Scientific Systems.

Roberto Martinez
padrino99@prodigy.net.mx

Zebra Z4Mplus... | Answered on Aug 28, 2011


frubioa: En el soporte de la cinta hay dos peque?as laminitas que mantienen fija la cinta, si estan muy dobladas hacia adentro, no sujetaran el rollo de cinta. Puedes levantar esas laminitas para ajustar el rollo.

Roberto Martinez
padrino99@prodigy.net.mx

Zebra Z4Mplus... | Answered on Aug 28, 2011


Aaron:

When multiple tags are waiting to print, to cancel should press the CANCEL button for more than five seconds. Also cancel print job in Windows spool. Roberto Martinez Mexico padrino99@prodigy.net.mx

Zebra Z4Mplus... | Answered on Aug 28, 2011


Laura: cuando conectas un zebra net a una impresora zebra, se habilitan en el setup las opciones de red, como lo es la IP, GATEWAY, etc, y asi sabras que el zebra net se ha reconocido.

Roberto Martinez
Mexico
padrino99@prodigy.net.mx

Zebra Z4Mplus... | Answered on Aug 28, 2011


The password is 1234. You can also run manual calibrate in the menu.

Zebra Z4Mplus... | Answered on Aug 26, 2011


You need to run the calibration procedure:

https://support.zebra.com/cpws/docs/z4mplus/z4mplus_man_cal.pdf

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Zebra Z4Mplus... | Answered on Aug 18, 2011


If the blank line is vertical (parallel to the print direction) then
Either the head is damaged at this point (dots missing) or you have something on the ribbon which prevents the head from doing the transfer.
Or the ribbon is faulty and you have to change the ribbon

Zebra Z4Mplus... | Answered on Aug 12, 2011


The data is sent by the host computer.
You have to change the data sent to the printer.

Zebra Z4Mplus... | Answered on Aug 04, 2011


Yes this printer is supported by windows 7. here is the link to the driver:-

http://www.zebra.com/id/zebra/na/en/index/drivers_downloads/drivers/results.html?productType=7

Hope that helps you.

Zebra Z4Mplus... | Answered on Jul 25, 2011


Set printer to use direct thermal and make sure this is not over ridden by label sent to printer ( This setting can be over ridden by software). Either in printer driver or label format.

Zebra Z4Mplus... | Answered on Jul 07, 2011


No you can only adjust font size in the software or document prior to printing. Hope this helps!!

Zebra Z4Mplus... | Answered on Jun 21, 2011


This error iscaused by an incorrect configuration setting in the print queue. Both theprinter's Preferences and the printer's Default settings need to reflect theproper label that you are using. Reconfigure your printer with thesefollowing steps: Step 1: Right-click on theprinter's queue and select "Properties". Select the "Printing Preferences"button at the bottom. Step 2: Be sure the Paper Sizereflects the of the labels you are using. In this example, the Paper Sizeis set to the Hedberg standard of: 4.00" x 4.00" - (10.16cm x 10.16cm) select"OK" to continue. Step 3: Select the "Advanced"tab and then select the "Printing Defaults" button at the bottom. Step 4: Be sure the Paper Sizereflects the of the labels you are using. In this example, the Paper Sizeis set to the Hedberg standard of: 4.00" x 4.00" - (10.16cm x 10.16cm) Select"OK" to continue. You can close the Printer Properties box and test the labelsand verify that they are now printing correctly. Hope this will help you.

Zebra Z4Mplus... | Answered on Jun 20, 2011


Perform a Manual Calibration:
Perform a media and ribbon sensor calibration to reset the sensitivity of the sensors so the
media and ribbon are detected more accurately. If you change the type of ribbon or media,
your printer may operate better if you perform this calibration.

Calibrate Media and Ribbon Sensors
Use this procedure to adjust the sensitivity of the printer's sensors. In a
printer that has the Thermal Transfer option installed, both media and
ribbon sensors are adjusted. In a Direct Thermal printer (no Thermal
Transfer option installed), only media sensors are adjusted, and the LCD
displays for ribbon do not appear in this procedure.
Important • This procedure must be followed exactly as presented.
All of the steps must be performed even if only one of the sensors
requires adjustment. You may press the left arrow at any step in this
procedure to cancel the procedure.
How to select this parameter:
1. Press ENTER to start the calibration procedure.
The LOAD BACKING/REMOVE RIBBON prompt displays.
2. Open the printhead.
3. Remove approximately 8 in. (203 mm) of labels from the backing,
and pull the media into the printer so that only the backing is between
the media sensors.
4. Remove the ribbon (if used).
5. Close the printhead.
6. Press ENTER.
The message CALIBRATING PLEASE WAIT displays.
The printer adjusts the scale (gain) of the signals that it receives from
the media and ribbon sensors. On the sensor profile, this essentially
corresponds to moving the peak of the graph up or down to optimize
the readings for your application.
RELOAD ALL displays.
7. Open the printhead and pull the media forward until a label is
positioned under the media sensor.
8. Reload the media and ribbon (if used).
9. Close the printhead.
10. Press ENTER.
The message CALIBRATING PLEASE WAIT displays.
The printer does a calibration; during this process, the printer
determines the label length. To see the new readings on the new scale,
print a sensor profile.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Zebra Z4Mplus... | Answered on May 25, 2011


check to see if part of a label is stuck to the print head. If not then clean the print head with alcohol. wipe it only in one direction. If this still fails then you will have to replace the head.

Zebra Z4Mplus... | Answered on Apr 23, 2011


The problem with this type of printer is that when you use true type fonts, they are downloaded as graphics. If you have a field which changes on each label there is an overflow of memory. The solution is to use internal fonts for continuously changing datas

Zebra Z4Mplus... | Answered on Apr 11, 2011


from what your describing sounds like its 1 of 3 things,

firstly, take the paper out and let it warm up in a light cupboard or under a florsecent light, let it heat up a bit and then replace it in the printer. try printing now and more than likely it will print. Reason being is that the paper has moisture build up on it, keeping new paper in a warm dry place will help with this. If this wasn't your problem then lets try the next thing.

purchase and replace the platen roller, more than likely part of the roller is damaged (the part that your text label falls on, replace it. you can also redesign the lablel so it falls on another part of the label.

Zebra Z4Mplus... | Answered on Mar 31, 2011

Not finding what you are looking for?
Zebra Z4Mplus Label Printer Logo

285 questions posted

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Z Zebra

  • Z Zebra

Most Popular Question

z4mplus doesnt recognize media label

  • Office Equipment & Supplies
Loading...