20 Most Recent Zebra Z4Mplus Label Printer - Page 5 Questions & Answers


run some labels and the warning go off. it is not a problem

Zebra Z4Mplus... | Answered on Mar 26, 2011


run calibration ribbon and media, and save. reset the printer and run Sensor profile.

Zebra Z4Mplus... | Answered on Mar 26, 2011


check the darkness, check if the labels you use need to print with ribbon (Termal Transfer)

Zebra Z4Mplus... | Answered on Mar 26, 2011


faulty Logic Board, need to be replace.

Zebra Z4Mplus... | Answered on Mar 26, 2011


drop the darkness to low level, check if the format have to much black lines, mins to much hit on the same place. possible need to change the format.
w.c.s the printhead, if not original from zebra, can do that, need to replace.

Zebra Z4Mplus... | Answered on Mar 26, 2011


check if seting from LABEL TOP is on 0000, check the driver as well.

Zebra Z4Mplus... | Answered on Mar 26, 2011


check the setings, change the setings, Media TYPE from Termal Transfere to Direct Termal.
if necessery, reset the printer to Factory Defult.

Zebra Z4Mplus... | Answered on Mar 26, 2011


possible becouse the tear off position stop the gap on the wrong spot and wen you cut the label, left some label with glue expose, and wen you send other print, the printer make the backfeed and the label go stuck on the white rollar.
go througt the setings to TEAR OFF, and ajust to the front or back, untill hav the best gap/label rest possition and cut proply. don't forget to save (press setup button twice)

Zebra Z4Mplus... | Answered on Mar 26, 2011


Reset the printer to factory defult

Zebra Z4Mplus... | Answered on Mar 26, 2011


if you sending a file (ex. pdf or picture). to the printer, can do this, if you send the proper format with normal fonts (caracteres))to the printer, work fine. build new label from zebradesigner

Zebra Z4Mplus... | Answered on Mar 26, 2011


run the manual calibration, check if the printer stop the labels on the gap. if yes, check the laber format (length and with can be biger than the labels..

Zebra Z4Mplus... | Answered on Mar 26, 2011


check the driver, try to install (seagulldrivers} WWW.SEAGULLSCIENTIFIC.COM

Zebra Z4Mplus... | Answered on Mar 26, 2011


check the setings, reset to factory defult.

Zebra Z4Mplus... | Answered on Mar 26, 2011


increase the darkness to 22-25, clean the white rollar unther the printhead.

Zebra Z4Mplus... | Answered on Mar 26, 2011


can you be more especific? Thanks.

Zebra Z4Mplus... | Answered on Mar 26, 2011


if is on warranty, send to the reseler, is possible need to flash the firmware again.

Zebra Z4Mplus... | Answered on Mar 26, 2011


check if the setting FORMAT CONVERT is with some numbers, please change for NONE.
This seting change the resolution from Printhead 200dpi or 300dpi or 150 dpi or none, none mins, if you have 200dpi printhead, print 200dpi resolution(small fonts). if have 300 dpi, print with 300 dpi resolution, if have 300 dpi(very small fonts) printhead, can print 150dpi(big fonts) if change this setting.
if ok, check the driver or your software.

Zebra Z4Mplus... | Answered on Mar 26, 2011


if not using ribbon, change the setings from termal-transfer to direct termal.or vice-versa.

Zebra Z4Mplus... | Answered on Mar 26, 2011


create a file (notpad)
write this comands
^XA
^KP4567
^XZ
close and save password.zpl
send to the printer (driver - send file)
to reset to 1234
^XZ
^JUF
^XZ

Zebra Z4Mplus... | Answered on Mar 26, 2011


this feature just appear in the setings if some network cable is connect. if have connectivety, go througth the setings and see IP adress/subnet mask, gateway, and can configurate properly (permanent or DHCP.

Zebra Z4Mplus... | Answered on Mar 26, 2011

Not finding what you are looking for?
Zebra Z4Mplus Label Printer Logo

285 questions posted

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Z Zebra

  • Z Zebra

Most Popular Question

z4mplus doesnt recognize media label

  • Office Equipment & Supplies
Loading...