Symbol LS 4278 Barcode Scanner - Page 2 - Answered Questions & Fixed issues
When I scan a barcode with the Symbol LS 4278
There was probably some kind of ADF Rule applyed, please scan the barcode Set All Defaults and Erase All Rules from ADF Chapter in the manual for LS4278 aailable here http://support.symbol.com/support/search.do?cmd=displayKC&docType=kc&externalId=6983404apdf&sliceId=&dialogID=190394003&stateId=1%200%20190388491
I have a new LS4278
Hi,
Welcome to Fixya. If you are receiving Three quick beeps (all the same tone) it means that the battery is low. Since this was a brand new device then you need to charge it up same with other device that uses a battery that you need to change before you use it. I attached the manual below so that if you have questions about the functions of the Scanner you can use it a reference.
LS4278 Reference Manual
You can also download the latest software and driver on the link below
LS4278 Drivers and Software
If you have questions please let me know. Thanks for using Fixya.
When my scanner ls4278 is on the cradle it has a
I was also unable to find a solution for you. There are only supposed to be 2-leds in the cradle, 1-green and 1-amber. Maybe it is a battery temp fault, and it has somehow been misread. If you have another docking station and another gun, try swapping them to see where the fault lies. If on the good station the gun shows the same error, you know the fault it with the gun, not the cradle. Hope this has helped!
Handset green light is flashing
Hi, there are detailed instructions for replacing the battery in the
LS4278 Product Reference Guide on page 27 of 414.
Use a philips screwdriver and turn the screw in the base of the scanner counter clockwise to remove the latch at the bottom of the scanner.
Turn the scanner upright to slide the battery out.
Disconnect the battery clip.
Reattach the battery clip.
Make sure the new battery is securely in well of scanner.
Attach and close latch.
Use philips screwdriver to press down gently and turn screw clockwise to lock latch in place.
I want the cursor from my computer to
Do you have the manual/CD that came with the scanner? If so, you should be able to "create a new rule" and include the TAB as a "suffix" to the scan string. Just be aware that this behavior will always be in place (unless you disable the rule) so if you use the scanner for another application this may not be the best option.
My Symbol LS4278 will not transfer data to the
Hello,
Be sure to use a full PS2 to USB adapter not just the plug adapter. The one to use has the cable and a small encoder box in the middle, usually for keyboard and mouse together. We have seen some of the cheaper adapters not pass the proper voltages to the scanner for a good read. The ones we suggest to our customers is made by Belkin part # F5U119VE1SN
I hope this helps, if so please rate our solution.
Buddy
Corporate Computer
www.ccl-la.com
Red Beam stuck on
You sound like a pretty experienced user. You've likely already tried pulling the battery for an hour replacing the battery, and then defaulting.
If you haven't try it. Symbol gear is excellent, but even BMW'a break occasionally. Our shop is one of many that can effect a hardware repair.
Enter function
Hi Lee,
It can be done by programming the scanning the 'Send Enter Key' barcode twice, from the owners manual.
eg
Scan the barcodes -
Send All Data, Send Enter Key, Send Enter Key, Save
My Kenwood 1 ton inverter ac outer not starting some times start show compressor symbol and then turn off and not start again doesn't show any error please guide
If your Kenwood 1 ton inverter AC is having trouble starting and sometimes shows the compressor symbol before turning off, there may be a few things you can check to diagnose the issue.
- Power Supply: Check that the AC is receiving proper power supply, and the circuit breaker is not tripped. Sometimes, due to voltage fluctuation, the compressor may not start.
- Dirty Air Filters: Check the air filters and clean them if they are dirty. Dirty air filters can reduce the airflow and cause the AC to malfunction.
- Faulty Thermostat: If the thermostat is faulty, it may not be able to detect the temperature properly and cause the compressor to not start. You can check this by setting the temperature to a lower level and see if the AC starts.
- Low Refrigerant Level: Check the refrigerant level in the AC. Low refrigerant levels can cause the compressor to not start.
If none of these steps solve the issue, it may be best to contact a professional AC technician to diagnose and repair the issue.
How to type degree symbol on mac
There are a few different ways to type the degree
- Use the keyboard shortcut: Press and hold the Option key, then press the letter K on your keyboard. This will insert the degree symbol.
- Use the character viewer:
- Go to the Edit menu and select Emoji & Symbols.
- In the search field, type "degree".
- Double-click the degree symbol to insert it into your document.
- Use the ASCII code:
- Press and hold the Option key and the Shift key.
- Press the number 8 on the numeric keypad. This will insert the degree symbol.
I hope this helps! Let me know if you have any other questions.
Videocon ac remote not working
Hi,
Please reach out to videocon on twitter to help take care of this issue: @VideoconIndia . You can tweet their handle with the issue included.
You can also call 1800 1370 444 to reach them. I believe that is a number based in India. Thank you.
Not finding what you are looking for?