There are plastic clips to hold the keyboard. With a suitable flat screwdriver, you can open it. You can damage the plastic body if use force to open it.
The P6 and P7 connectors you found inside your HP 6000 tower are indeed related to the CD/DVD drive. They are typically used to provide power and data connections to the drive. Here's how you can connect them properly:
1. Power Connection (P6): The P6 connector is usually a 4-pin Molex power connector. It provides power to the CD/DVD drive. Locate a corresponding power socket on the back of the CD/DVD drive. It should have four pins and match the shape of the P6 connector. Connect the P6 connector to the power socket on the drive. Ensure it is securely attached.
2. Data Connection (P7): The P7 connector is usually a 40-pin IDE or SATA data connector, depending on the type of CD/DVD drive installed. Locate the corresponding data socket on the back of the CD/DVD drive. It should have either a 40-pin IDE connector or a smaller SATA connector. Connect the P7 connector to the data socket on the drive. Make sure it is properly aligned and securely connected.
After connecting both the power (P6) and data (P7) connectors, you can close the tower and start the computer. Windows should then detect the CD/DVD drive, and it should appear in the Device Manager. If the drive is still not recognized, there might be additional factors at play, such as driver issues or hardware problems with the drive itself.
If the CD/DVD drive continues to have issues or is not recognized by the system, it may be necessary to troubleshoot further or consider replacing the drive if it is no longer functioning properly.
Please note that the exact connector types and locations may vary depending on the specific model and configuration of your HP 6000 desktop computer. If you have difficulty locating the appropriate connectors or need further assistance, it is recommended to refer to the computer's user manual or contact HP's customer support for precise instructions tailored to your specific model.
Better to have FULL 'make model' and the Service Tag Number, but it appears to be a well documented issue.
If you want to fix the HP laptop not turning on power light blinking issue, you must first check the BIOS battery. Usually, this is located near the motherboard. To remove it, you need to press and hold the power button for about 30 seconds. This should restore the laptop's BIOS.
hp.comhttps://support.hp.com > ish_1997210-1528385-16
52 steps
1.
Turn off the computer.
2.
Disconnect the AC adapter.
3.
Disconnect all nonessential peripheral devices, such as printers, scanners, external hard drives.
It appears to be a known issue
Fix 1: Hard reset your laptop
Remove the power, hard drives, the battery and any attached peripheral devices. Press and hold the power button for 60 seconds and release. Put your battery in and plug the charger. Then don't plug anything else.Nov 20, 2019
If you are experiencing issues with HP Support Assistant, here are a few steps you can try to fix it:
Update HP Support Assistant: Make sure that you have the latest version of HP Support Assistant installed. To check for updates, open HP Support Assistant and click on "Settings" > "About".
Restart the HP Support Assistant Service: Press "Windows key + R" to open the Run dialog box. Type "services.msc" and press Enter. Scroll down and look for "HP Support Assistant Service", right-click it and select "Restart".
Clear the cache and temporary files: Open HP Support Assistant and click on "Settings" > "Health Analysis". Click on "Clear selected" to clear the cache and temporary files.
Run HP Support Assistant in compatibility mode: Right-click on the HP Support Assistant icon on your desktop, select "Properties" > "Compatibility" tab. Check the box for "Run this program in compatibility mode for" and select the previous version of Windows.
Reinstall HP Support Assistant: If none of the above steps work, try uninstalling and then reinstalling HP Support Assistant. To do this, go to "Control Panel" > "Programs and Features" > "HP Support Assistant" > "Uninstall".
If you continue to experience issues with HP Support Assistant, you can contact HP support for further assistance.
There could be several reasons why your HP laptop is not turning on and not charging even after installing a new power button board and DC in port. Here are a few possible causes and troubleshooting steps you can try:
Battery: Even if the laptop is connected to the charger, if the battery is faulty or dead, the laptop may not turn on. Try removing the battery and plugging in the charger directly to the laptop. If the laptop turns on without the battery, then it's likely that the battery needs to be replaced.
Charger: Check if the charger is working properly. You can try using another charger with the same voltage and amperage to see if the laptop starts charging. If the laptop starts charging with a different charger, then your original charger may be faulty.
Power Jack: Make sure the power jack is properly connected to the motherboard. If it's loose or not properly seated, the laptop may not charge or turn on. You can try reseating the power jack or replacing it if it's damaged.
Motherboard: If none of the above steps work, then the problem may be with the motherboard. A damaged or faulty motherboard can prevent the laptop from turning on or charging. In this case, you may need to take the laptop to a professional repair technician or consider replacing the motherboard.
In summary, the laptop may not turn on even when connected to the charger if the battery is dead or faulty, the charger is faulty, the power jack is loose or damaged, or the motherboard is damaged. It's important to troubleshoot each of these components to identify the root cause of the issue.
It sounds like you have a faulty battery or the laptop has suffered a power surge. To resolve the issue, you can try a few things. First, try resetting the laptop by holding down the power button for 30 seconds. If that doesn't work, try replacing the battery with a new one. If the laptop still won't turn on, it's likely that you sustained a power surge in the DC port and will need to get it serviced at an HP authorized service center.
Question moved from Laundry Dryers to one of the laptop categories.
All questions need 'make model (what it is)' and in the case of a laptop the Service Tag number. You also don't tell us what 'the units' are either. Printers are connected via USB to the Laptop.
The socket with 3 or 4 prongs is likely the external mouse socket. It may even be the mains adapter socket.
..
