Samsung SyncMaster 940MW 19" LCD Monitor - Answered Questions & Fixed issues
940mw vertical sync instability
Try another monitor to be sure it is the monitor not the computer. If it is the monitor you need to take it to the repair shop. Be sure you are operating it in the proper range.
3/7/2015 8:22:08 PM •
Samsung...
•
Answered
on Mar 07, 2015
•
72 views
Won't turn on no power
You more than likely have bad capastors or diodes that will require taking the monitor apart then the parts replaced they will have to be soldered in and a small solder gun will be needed to keep heat as low as possible so the board doesn't get damaged. Use only japanese made gold rated parts
3/18/2014 12:40:01 PM •
Samsung...
•
Answered
on Mar 18, 2014
•
142 views
Pc screen will not come on
HI,Check you power port.Check it Power Cable.If Monitor not open then may be monitor damage. If PC ask then SMPS check it. Because all power supply to SMPS. Next to check it mother board power come or not. Then RAM slot check, and checking carefully. One time all power section and connector disconnect and some time wait and again proper way connect all device. May be solved you problem.Thanks..
10/10/2013 4:43:19 PM •
Samsung...
•
Answered
on Oct 10, 2013
•
83 views
The tv s autostore will not retune
i think in your TV...... design ..... is such that once channels are autostored it cannot be retuned ..... so you try this ...... it may work ......... disconnect tv antenna cable ( or local tv channels cable ) from your TV & then click autostoring (auto tunning ) ..... definitely it will scans (search for channels ) ..... but since no cable is connected no channels will get stored ...... but previously autostored channels will get removed ...... so now again connect your antenna cable or local tv cable & then click autostore ...... it will scan for channels .... like this you can retune ....... but remember again you may get same quality of picture which you got earlier ..... if you want better quality of picture you have to use signal amplifier (increases cables signal's strength - then picture quality improves ) .....
11/5/2011 8:28:04 PM •
Samsung...
•
Answered
on Nov 05, 2011
•
316 views
Syncmaster 940 mw says 'digital' on the
Hello,Yes, You will need a digital decoder box. The tuner in the Samsung 940MW TV does not decode digital signals. The digital input that you are seeing is for the DVI video input on the back that you use when you connect the unit to a DVI port on a computer. Any of the digital decoder boxes from Radio Shack, Walmart or Best Buy type stores will work just fine.I hope this helps, If so please rate my solution.
10/31/2011 2:06:32 AM •
Samsung...
•
Answered
on Oct 31, 2011
•
249 views
On and off switch not working
Hello Michael,The most common problem with the Samsung 940MW units that don't turn on is a failure of the power supply board. There are parts called capacitors that fail which in turn causes the power supply to not startup correctly so the monitor never powers up. Here is a link to a repair guide that should get you back watching tv and using the monitor in no time.
http://www.ccl-la.com/blog/index.php/repairing-the-samsung-940mw-lcd-tv/I hope this helps, if so please rate my solution.
10/31/2011 2:03:16 AM •
Samsung...
•
Answered
on Oct 31, 2011
•
205 views
My samsung lcd tv screen is going blank or black
First, look at the screen in darkened room to see if you can see any slight glow from the screen, if it does, then the problem can be the T-CON (not getting the 12vdc) or the main logic board not feeding the signals to the T-CON board.
if not, next place to check will be the power supply module, make sure it has 24vdc which is required by the backlight inverter to work, the reason for not having 24vdc can be from bad DC filter caps (leaking/bulging top, high ESR) or short circuits in the inverter board which will cause the 24vdc supply to go into shutdown mode, so you may have to disconnect the power cable that feed the inverter board to see if the 24vdc will work without the inverter board hookup, you will need to apply about 3~4 amp of load to the 24vdc to make sure it can handle that. There are fuses on the backlight inverter boards also. So there is some troubleshooting you will have to do to find out the causes of the problem you are having.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:
Basic LCD monitor and TV troubleshooting guide:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
http://www.fixya.com/support/r7406380-tv_training_manuals
Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.Or www.digikey.com, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series.
4/10/2011 1:33:51 AM •
Samsung...
•
Answered
on Apr 10, 2011
•
212 views
My lcd tv samsung sycnmaster
Audio comes directly to multimedia LCDs and has nothing to do with display.
Usually, the capacitors are the casue of such blackouts. So, it is recommended that you check the capacitors/ other components such as invertor board and CCFL (lamp), which may be failing or heating up.
Hope it helps! Good Luck!
CreativeTECH
4/9/2011 11:11:45 AM •
Samsung...
•
Answered
on Apr 09, 2011
•
118 views
Ive had my samsung 940mw
monitor led didn't light mean power cable is damaged or monitor you can try
good luck
1/8/2012 5:02:42 PM •
Samsung...
•
Answered
on Jan 08, 2012
•
529 views
I have a samsung syncmaster
Make sure that under display properties in your computer, that the laptop is outputting an image. The PC option will not show up unless there is a signal to the monitor from the laptop.
3/9/2011 8:19:46 PM •
Samsung...
•
Answered
on Mar 09, 2011
•
345 views
Not finding what you are looking for?