20 Most Recent
Ricoh Aficio CL7200 Laser Printer - Page 3 Questions & Answers
I have very large magenta
Color streaks are typically caused by the photoconductor unit (which contains the drum) for that specific color, so your most likely solution is to replace the magenta and yellow photoconductor units. For the CL7200, all 3 color photoconductors come in one kit, EDP #402305. Replacing the magenta and yellow PCUs will more than likely get rid of your streaks.
If you replace the PCUs and one or both of the streaks are still there, you'll need to replace the developer units (EDP #402306) but I'd be very surprised if the new photoconductor units don't get rid of the streaks.
The reason you're not getting a "replace PCU" or "replace developer unit" message is because those messages only come up after a preset number of copies; they have nothing to do with the actual image quality and condition of the units.
If you want to make sure the photoconductor units are the problem, swap the yellow or magenta PCU with the cyan PCU (since that one isn't giving you streaks) temporarily, and see if you start getting cyan streaks instead of the other color. If that happens, you can be sure it's the PCU causing the problem.
Error sc545, how to solve?
sounds like you have a fuser error code to reset hit clear modes (yellow button) 1-0-7 then the clear (orange) button continue holding down until screen changes once you are in .. turn copier off.. if there is nothing wrong the problem should go away. if there is another problem with copier it will come back make sure everything is closed all doors and covers and the fuser is pushed all the way in.
The colors and images are printing well, but there
sounds like the drum or drums needs replacing or possibly transfer belt cleaning blade not doing its job worn out or spring fell of it. Most likeley to be a drum though.
i think they r 60 or 80 k life
The colour settings are not right on my Ricoh
On the CL7100, you can run the color calibration procedure, and the machine should set itself up for optimum color. Just go into the menu, and under the Maintenance heading choose Color Calibration.
Is the color still off after running the calibration? Is it only one specific color, or all colors? What about when you only print black & white?
The image density should typically be left at the default values for optimum print quality. However, if you need to adjust it, you can go from -3 to 3. In the menu, go to the Maintenance category and then choose Image Density and then the color that you want to change. Adjust the value and press Enter, then run a test copy to see if it helps at all. If not, reset it back to the value that it was (probably 0).
If only one color is giving you a problem, even after running the color calibration, you might need to replace the developer unit for that color.
How to get a copy count on a ricoh 7200 printer
To view the copy count, you'll have to print a config page. Press Menu, then scroll down until you see List/Test Print and press OK. Choose the Config Page option, and you'll get a page or two of information, with the copy count (broken into black and white and color) listed near the top of the first page.
I have two ricoh cl7200
Clean the fuser drum will resolve your problem. Also check and clean the feeder rollers.
Revert back for more assistance and provide your valuable feedback/rating.
Thank you for using Fixya.
I have a Ricoh CL7200 with error sc551.
Hi
Thanks for using FixYa. Error SC551 means that the Pressure
Roller Thermistor is Open. To resolve the issue you’ll need to replace the
thermistor, its better to replace both the rear and middle one. Please do accept the
solution if the issue is resolved or post a comment for further
assistance.
Thanks
Rylee
Waste toner
You have to "tell" the printer that you have "emptied" the receptacle. Depending on the model of printer, you may either need to replace it, or use the controls on the printer to "logically" do a "reset" operation.
Not finding what you are looking for?
