20 Most Recent Ricoh Aficio CL7200 Laser Printer - Page 4 Questions & Answers

soon you are going to be out of black ink and you will need to replace the cartridge
its just a warning that you are low on ink

remove the fuser unit and behind the unit there is a guide plate with little star wheels to guide the paper into the fuser those wheels are either dirty or damaged if damaged you will need to have them replaced
also you may want to clean the K laser assy there is a long green handled tool in the front door that fits in slots above the drums run it through a couple of times to clean the laser **** glass and you should be good.
clean the star wheels with alcohol and try not to bend them as they can cause jamming issues once they are bent.

good luck

in the RPCS driver have you added all of the accesories?
if not then this is why you can not collate just go into printers folder right click the rpcs driver go to properties and select then hit accessories select all applicable options and apply changes close out of the driver completely go back to a document and try to collate using the rpcs drivers.

this should fix your issues

Probably a blockage in the toner supply hose, or defective pump. Either way, it will need service.

A 440-1 is a black drum motor lock. The waste toner in the black pcu is backed up, more then likley. It is not easy to fix. You could replace the black pcu but it will happen again. The usual problem is oil in the main waste toner system. It clumps up the toner and clogs the part where all the waste toner comes together for entry into the waste toner bottle.

Windows 98 is not compatible with your new printer driver. You have to upgrade your operating system to at Windows XP.

It sounds like the transfer belt needs to be replaced. They get scratched up and milky looking and the sensors can't see the color reg marks good enough. It could be other things also but the transfer is a good place to start.

The developers almost never streak. I would be looking at your PCUs. Developers have a tendency to leave voids and dust the paper. PCUs tend to streak as the cleaning blade and charge roller wears out.

Fuser PM reset

1. Hold the 'up' and 'down' arrows together for 5 seconds or longer.

2. Release the arrow keys and press the 'enter' key.

3. Select '2. Engine' - Then go to option '7.'

4. Go to SP7804-016 (PM Counter Reset>Fuser) and execute. Shows results=OK

5. Turn the machine off and on.

All done.

The code may go away if you power on/off, but it will continue to return. It is a problem with the black development unit - replace it.

* please rate me :)

I think the code is a black pcu motor lock. Replacing the black pcu might fix it, but the black waste toner section could be backed up.

May need to change the color developer units

In Print Settings make sure the original size is 8 1/2 by 11 and print out size is 11 x 17

Ricoh Aficio 240W Plotter Error Code SC 401-00

Copytechnet https://www.copytechnet.com > forums > 108927-rico... May 4, 2016 - On old Ricoh Aficio's SC401 used to be a Transfer error, but on the 240 its ID Sensor, could be dirty, could be old Dev, could be a loose ... Ricoh MP2352 SC401- Strange problem Jul 28, 2021 Error Code SC-401 Sep 12, 2014 ricoh mp 3352 - error sc401 Dec 11, 2020 Ricoh mp 2851 SC 401 Jul 11, 2017 More results from www.copytechnet.com

Error Codes > Ricoh > MP2553 > Code SC401

Printcopy.info https://printcopy.info > code=SC401 Code: SC401 · Description: Transfer positive electrode current error A transfer roller current leak signal is detected. · Causes: • High voltage supply board set ... Missing: W2401 ‎' Show results with: W2401

Error Codes > Ricoh > Aficio 2090 > Code SC401

Printcopy.info https://printcopy.info > code=SC401 Code: SC401 · Description: Transfer roller open error · Causes: • Transfer power pack defective • Poor connection between the transfer current terminal and the ...

If your Ricoh Aficio MP C2800 is showing "toner undetectable" messages for all four toner cartridges and the yellow and cyan colors are not showing up in copies, there may be several potential causes for this issue. Here are some troubleshooting steps to help you resolve the problem:

1. Check Toner Cartridges: Ensure that all four toner cartridges are correctly installed and securely seated in their respective slots. Make sure there are no protective seals or tapes left on the cartridges.
2. Shake Toner Cartridges: Sometimes, toner inside the cartridges can settle or clump, leading to detection issues. Gently shake each toner cartridge side to side to redistribute the toner evenly.
3. Replace Toner Cartridges: If the toner cartridges are old, empty, or expired, replace them with new, genuine Ricoh toner cartridges.
4. Clean Contacts: Dust or debris on the toner cartridge contacts can interfere with communication. Use a soft, lint-free cloth to clean the electrical contacts on both the toner cartridges and inside the printer.
5. Check Developer Unit: The developer unit in the printer plays a crucial role in toner development and transfer. Ensure that the developer unit is clean and free from any obstructions.
6. Perform a Firmware Update: Check if there are any firmware updates available for your Ricoh MP C2800 printer. Updating the firmware might address known issues and improve printer performance.
7. Reset the Printer: Power off the printer, unplug it from the power source, wait for a few minutes, and then plug it back in. Power the printer on to see if the issue resolves.
8. Check Toner Detection Sensors: The printer uses sensors to detect the presence of toner cartridges. Verify that these sensors are functioning correctly and not blocked by any debris.
9. Perform a Factory Reset: As a last resort, you can try performing a factory reset on the printer. However, be aware that this will reset all settings to their defaults, and any custom configurations will be lost

Question edited tor a lot more clarity and add MAKER, but NO MODEL NUMBER! All questions need full make and model.

Ricoh Aficio 200 - Error Code: SC390

PrintCopy .info https://printcopy.info > code=SC390 Code: SC390; Description: TD sensor error 1. The TD sensor outputs less than 0.5V, 20 s after the TD sensor initial setting has been performed. Missing: cod ‎' Must include: cod

SOLVED: How fix sc390 cod of ricoh

Fixya https://www.fixya.com > ... > Ricoh The closest thing is the sc390 code, which means either the toner density sensor or the developer has gone bad, and typically replacing the PCU can fix that ...

• SOLVED: Code SC 390

  https://www.fixya.com > ... > Aficio MP6001 Copier Code SC 390 the code SC390 occurs when power on the machine. ... Service code sc 390 RICO Aficio 1015 coppier ... Sc 390 cod. what this?

Error Code sc 390

Copytechnet https://www.copytechnet.com > 56632-sc-390-a Sep 24, 2011 - I've got an Aficio 1018 that's generating sc390 after every 10 copies. I recently fitted new drum, cleaning blade and developer and changed ... Missing: cod ‎' Must include: cod

• Error code SC 390

  https://www.copytechnet.com > forums > 47571-error... Dear all Experts i often got an error code sc 390 on my ricoh aficio 270.kindly tell me what to do with this problem.

RICOH Error Code List - mtechsinfo.com

mtechsinfo.com http://www.mtechsinfo.com > files > Ricoh Erro... PDF SC-390-2. Toner density sensor error. SC-391. Developer bias problem or FU103 on Aficio 550/650 Image storage address error. Aficio 551, 551P, 700, 700P. 14 pages

Question edited for a lot more clarity and toss in some CAPS. Question moved to maker category. Printer set to wrong size paper. Computer word processing program set to wrong size. For example Letter size paper in Printer and Legal size in the Settings of what is saying to print the document. The paper is too small.