20 Most Recent
Maytag Neptune MDG5500AW Gas Dryer - Page 5 Questions & Answers
Manual
If you remove the top, then the front, there is a technical spec sheet in the dryer itself. It is taped to the side or the rails.
Very squeaky drum
Hi parinst...Yes you can do this job with limited tools and knowledge.This information will apply to your gas heater, I wrote it for an electric dryer...--------------------------------------------------------------------------------------------------- ALWAYS UNPLUG YOUR DRYER BEFORE STARTING ANY REPAIRS
Your problem sounds like the drum rollers have flat spots on them or in need of lubrication, or maybe your drum belt has slipped off of the idler arm pulley.
Note: This method works with most front loading machines. Remove the electrical console that holds the timer switch, start switch, etc. from the top of the dryer if you have to.Note: Some tops hinge and tilt backwards so they do not have to be removed and the electrical console with stay with the lid.Also remove the lint filter and the screws holding the lint filter housing in place. Be REAL CAREFUL not to knock any of the wires off of the timer switch. Then remove the top of the dryer.Remove the front of the dryer by removing two screws located on either side of the top of the dryer housing and unplug the door switch. This will expose the drum and belt. Remove the drum and belt and this will expose the drum rollers, idler arm pulley and motor.Now is a good time to replace the front felt seal on the drum if it needs to be replaced. Be sure to use a good grade of weatherproof cement on the seal to glue it to the drum, sometimes the glue is furnished with the seal.Now is also a good time to check the belt to see if it has slipped off of the idler arm pulley and also to check the belt condition for wear.Be sure to note the route of the belt, this will come in handy when you go to reinstall the belt.Check your drum rollers for flat spots or wear, if they have flat spots or wear they will make a thumping type of noise.If your drum rollers have too much wear on them replace them.If the drum rollers don't have flat spots or wear on them and are only squeeling then they probably only need lubrication. Remove the rollers and clean the shafts that the roller rolls on, remove any hair,dust,etc from roller and shaft.Lubricate the shaft of the rollers with a good grade of machine oil such as 3 in One oil, or a light lubricant like Vaseline. Reassemble the dryer.Plug back into your electrical receptical. This should solve your noise problem.Please take time to rate me Bud
Timer wont work
Sure , take door off by unscrewing the two screws (be careful they don't strip ) remove the front panel, detach the wires going to the motor , turn the unit on if you get 120v to the motor your motor need to be replaced if not your timer may be faulty .one note check your belt if its torn it may have a sensor that will prevent the unit for turning on. good luck APPLIANCES R EN
Gas smell
This is caused 95% of the time by a bad igniter, it does not light it constantly and will give this odor.The igniter light the gas to burn and heat, also make sure that the exhaust going to the outside is not kink or clogged at all this will also cause this problem.Here is the igniter to order.
Tumbles but does not dry
When you put your wet cloths in the dryer close the door. You should then turn on the dry cycle you wish, not the fluff option as there will be only air and gas dryer will not heat the cloths. Wait 30 ~ seconds after the dryer is turned on and listen for the gas to ignite and begin warming and drying the cloths. If you hear no bump sound like the ignition of the gas, then you have an ignition issue. It will require replacing the ignitor. All the best and good luck. Hope this helped.
Gas smell in maytag dryer
You have a gas leak from the gas valve being faulty. DO NOT use the dryer until you have replaced the valve! I have been doing appliance repair for 15 years and I have seen 7 homes that have burned down due to this very same problem. Please don't use the dryer!
Here is the new gas valve to order.Keep me posted!
Not finding what you are looking for?