Maytag Neptune MDE5500AY Electric Dryer - Answered Questions & Fixed issues


You have to work from the front. Pull the top then the front then you will be able to see everything. Pretty self explanatory.

Maytag Neptune... | Answered on Oct 02, 2019 | 3,425 views


Main Control Board 33003028

Is this the part you replaced?

Maytag Neptune... | Answered on Feb 21, 2018 | 372 views


Sure I will help you when that happens that means that your heater core is no longer operating and when the heater core doesn't work when your dryer doesn't heat up anymore so that's your problem I hope I have helped you please leave a response or Stars if I have helped

Maytag Neptune... | Answered on Feb 07, 2018 | 435 views


near fan blower ,had a fuse white by pass than try if work change it than clean the vent

Maytag Neptune... | Answered on Nov 14, 2017 | 99 views


the female is the switch! you can pop the top off and check with electric tester on ohms, make sure you unplug the drye
check the breaker make sure you have 220 volts a in the outlet !

Maytag Neptune... | Answered on Aug 16, 2017 | 67 views


sounds like a bad control board it seems like you have a letter missing in your model number ...I looked up the part ouch ..http://www.repairclinic.com/vwo1/Maytag-Dryer-Model-MDE5500AYW-ID-563862-Circuit-Board-Timer-Parts?s=t-mde550ay-%3d%3dd563862b4a8c13

Maytag Neptune... | Answered on Jul 26, 2017 | 169 views


Looks like your drive motor is locked up. It has an internal overload switch which cuts power off when motor gets too hot...Replacement of the motor on a used dryer is probably not the best choice as it can be quite pricey..

Maytag Neptune... | Answered on Jul 10, 2017 | 87 views


Disconnect power or turn breaker off for about 5 minutes. This may reset the unit. Otherwise you have an eror showing and need to retrieve the error code. Google your make and model followed by error codes a d you should get a link to retrieve the codes.

Maytag Neptune... | Answered on Aug 09, 2016 | 163 views


This may be from a key that is stuck on the panel. Press each key individually to see if all of them move up and down.

Maytag Neptune... | Answered on Jun 30, 2016 | 232 views


We have the same machine. The drum also broke so we had it professionally installed. It wasn't done well enough and after the 90 day repair warranty, other problems developed. We still don't have a dryer and the next repair is $500 as other parts were damaged and we didn't catch it within the 90 days.
Bottom line: do have it professionally installed but be sure to ask about their work guarantee. As soon as you have any problem at all, call them back.

Maytag Neptune... | Answered on Feb 07, 2016 | 476 views


on board fuse or control card cooked

Maytag Neptune... | Answered on Jan 25, 2016 | 57 views


sounds like its hung in a loop unplug wait a few min. plug back in

Maytag Neptune... | Answered on Dec 24, 2015 | 114 views


Type Maytag dryer timer problem into YouTube and see if the video comes up, thanks!

Maytag Neptune... | Answered on Dec 03, 2015 | 290 views


Type Maytag Neptune push pad into YouTube and see if the video comes up, thanks!

Maytag Neptune... | Answered on Apr 14, 2016 | 158 views


It might be the thermal cutoff switch. You could go online to see where it is located for that model dryer and have that tested.

Maytag Neptune... | Answered on Nov 26, 2015 | 57 views


Generally operation when cold that worsens with use indicates a component that is failing when hot. Start at the burner with the coils and work your way back to relays on the control. Sounds a lot like a bad coil on the burner. I have seen these do 2 complete loads then fail. Setting over night and cooling off will work again the same way. Intermittent conditions are a real challenge sometimes.
Eric

Maytag Neptune... | Answered on Nov 12, 2015 | 316 views


Check lint filter. Check blockages in the exhaust hose. Check that the flap outside your wall is not blocked and that the slats or flap opens OK. To get fast drying you have to have a good airflow into the drum and out of it.

Maytag Neptune... | Answered on Oct 22, 2015 | 62 views


a bearing in the back for your drum sounds like what you describe. It needs to be taken apart and the bearing lubricated with high temp grease

Maytag Neptune... | Answered on Aug 21, 2015 | 1,109 views


unscrew all the panels and clean everything with bleach and soap,clean it outside so you can use a hose,soak it down,let it sit without the doors on for a few days in the sun

Maytag Neptune... | Answered on May 12, 2015 | 80 views

Not finding what you are looking for?
Maytag Neptune MDE5500AY Electric Dryer Logo

2,008 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Dryers Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Maytag Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...