Maytag Neptune MAH6500A Front Load Washer - Answered Questions & Fixed issues


That is Failed Lock. If the door is not completely shut and the lock can not engage after several attempt you will get this code.

Maytag Neptune... | Answered on Apr 03, 2016 | 141 views


quite often it will be the door switch has failed

Maytag Neptune... | Answered on Jun 16, 2015 | 119 views


I would check the balance of machine by using a leveler and checking the bottom leg adjustment on all 4 legs then check the
suspension springs, counter weights, dampning straps etc.




washer-moves-violently-gives-lr-code-dn3wi03dqy3vjnwbm4uf5us1-3-0.jpg

washer-moves-violently-gives-lr-code-dn3wi03dqy3vjnwbm4uf5us1-3-2.jpg

washer-moves-violently-gives-lr-code-dn3wi03dqy3vjnwbm4uf5us1-3-5.jpg

washer-moves-violently-gives-lr-code-dn3wi03dqy3vjnwbm4uf5us1-3-9.jpg

washer-moves-violently-gives-lr-code-dn3wi03dqy3vjnwbm4uf5us1-3-14.jpg

washer-moves-violently-gives-lr-code-dn3wi03dqy3vjnwbm4uf5us1-3-20.jpg

washer-moves-violently-gives-lr-code-dn3wi03dqy3vjnwbm4uf5us1-3-27.jpg

Maytag Neptune... | Answered on Jun 11, 2015 | 246 views


The problem is that the seals are leaking and allowing water to attack the tub bearings.
You need new tub seals and bearings.....not as difficult as it may seem.
see u tube video on replacing maytag seals and bearings
Cheers Stan

Maytag Neptune... | Answered on Apr 02, 2015 | 338 views


change capasator

Maytag Neptune... | Answered on Mar 03, 2015 | 43 views


Remove the screws holding the door on , pull the door up and off then remove the two opposite side screws, pull the front panel off.you will see a metal bracket on each side that hold the top on remove those , now you should be able to get the switch

Maytag Neptune... | Answered on Aug 02, 2014 | 34 views


Check the door switch.

Maytag Neptune... | Answered on Aug 02, 2014 | 53 views


Is this unit brand new or has it been run before. Make sure the cycle is finished and power is off should open up. I if not unplug unit wait about a minute and then plug in again then try. Reset any fault .then try.

Maytag Neptune... | Answered on Aug 02, 2014 | 40 views


Your Maytag Neptune MAH6500A Front Load Washer has dimensions:

Width : 27"
Depth : 29"
Height : 42 1/2"
Capacity : 3.34 cu. ft.

http://www.ajmadison.com/cgi-bin/ajmadison/MAH6500AWW.html

Maytag Neptune... | Answered on May 22, 2014 | 227 views


Check for obstruction between inner & outer bowl.

Maytag Neptune... | Answered on Dec 21, 2013 | 45 views


change the seals

Maytag Neptune... | Answered on Sep 22, 2013 | 82 views


I have a Maytag front loader MAH6700AWW. I just pulled the pump lastnight because it had a quarter stuck in it and was making a terrible grinding noise. I was shocked to discover that there is absolutely no filter trap on this machine. If anything gets past the rubber boot, and coins can and do... you need to wish for luck in that you do not wipe out your pump. I was shocked that this machine had not filter trap between the pump impeller and the tub drain. All newer machines have these. The LG and most have a trap door on the front you open to access the trap. Some of the earlier front loaders required that the bottom front panel be removed. No such animal on this Maytag. Probably yours as well.

Maytag Neptune... | Answered on Apr 16, 2013 | 5,881 views


I've had the same issue with my Servis washer/Dryer since I moved recently. All the cycles seem to have doubled !! WebRepOverall ratingThis site has no rating(not enough votes)

Maytag Neptune... | Answered on Mar 01, 2013 | 195 views


E3 = Machine control is attempting to drive the motor but is not seeing any tach response.
Evaluate wire harness for loose or unhooked connections.

Post back the results.

Maytag Neptune... | Answered on Dec 05, 2012 | 52 views


What is the model number of your unit?

Maytag Neptune... | Answered on Nov 18, 2012 | 102 views


You will need to replace the door lock assembly. Here is the part to order. Below is a video to show you how to open the unit. This is a different model but the cabinet opens the same way.




Maytag Neptune... | Answered on Nov 13, 2012 | 115 views


The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these:

Motor coupler
Spin cycle
Siphoning
Water-inlet valve
Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning:

  • If it's spinning when you lift the lid, the coupler is fine.


  • If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.


Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.

Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.

Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.

Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.

Maytag Neptune... | Answered on Nov 12, 2012 | 983 views


you can get the parts break down pics at marcone.com

Maytag Neptune... | Answered on Oct 17, 2012 | 42 views


What is the model number?

Maytag Neptune... | Answered on Oct 17, 2012 | 26 views

Not finding what you are looking for?
Maytag Neptune MAH6500A Front Load Washer Logo

230 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...