Maytag Neptune MAH6500A Front Load Washer - Page 2 - Answered Questions & Fixed issues
Where do you put the soapin a maytag neptune
On the neptune washer, on the top there is a dispenser on the left hand side, lift up the lid, there will be 3 compartments, the compartment closest to the control panel is the one you put the soap into, the middle compartment is for bleach, the other one is for fabic softner.
Maytag neptune washer can not change the wash cycles
1) test the timer probably faulty,tight connection wires see the diagram how to test,and see the diagram in line black, how the contacts from timer control everthing in the washer.2) problem of cold water, is the cold water turn on? consult your owner manual for to see if acting abnormally3) check the selector is o.kGod bless you
What does nf mean
NF stands for no fill, which means you are not getting any water into the machine. This is either because the water valve has failed or is clogged, the water is turned off or the pressure switch thinks there is already water in the machine but the last is very unlikely. If you need further help, I’m available over the phone at
https://www.6ya.com/expert/jason_4570d45317834dd3
Neptune MAH9700AWW
I can only assume it's because you have no water connected to it. Some washers have a pressure switch that won't allow the machine to turn on without it being connected...try it and see what happens.
Washer will not drain
Check the drain hose for clogs. If that checks out, you most likely have a clogged or shot drain pump.
Fix a neptune washer
Will be a great a idea to download your instruction manual in www.maytag.com give your model, and get readyFollow the steps in section troubleshooting.God bless you
Maytag neptune washer model mah6500a, took the
Looks like another motor/motor control panel replacement. This machine has a faulty motor/motor control board, it has been re-engineered with a replacement. Has yours been replaced?
Have you found the tech sheet behind touch panel and placed machine in service mode to test?
We had the same issue, worked sporadically, didn't drain, got LR code then eventually stopped working.
Check your spin in service mode, if it doesn't spin properly you should find out here. It is a very simple repair in all actuality. Contact Maytag and they will sell you the parts for a discounted price, make sure that you buy directly from Maytag, also check your boot very carefully since that part will also fail and allow water to get into the bottom of the machine where you have electronics.
Maytag Neptune "nd" code
It is a drain pump issue, it is either a blocked or faulty pump or a fault in the electronic controller.
My dryer will not heat up.
The easiest way I know is to check the heating element, turn thr dryer on and try ranging slowly,a minute each through the cycles if no heat-it is almost immediate, I would SUSPECT the heating element. I do not know how to access it but it is basically a foot or so coiled wire like the old hot plate elements sometimes enclosed in a tin "heater box" to direct the heat. If they break-no heat. You have to before you start disconnect all power and remove the element and check for breaks and also use a multi meter to check for continuity(breaks that might not be visible.If this doesn't help I strongly urge a manual which should help you trouble shoot.Best Wishes
My door won't latch on Maytag Neptune. What parts
Hello,
I do not want to take away from what another says...however i seriously have doubts that replaing the door panels will fix that and i would replace the door latch thats fits into the cabinet if i were you
Gene
There is loud noise at rear of machine when in the
could be the bearing. does it sound like a freight train when the machine is in spin cycle. if your machine is still under warranty or contract, call it in for service. if its not, then you might want to think about purchasing a new machine.
I have a Maytag Neptune
Hello
& Welcome to FixYa
The
problem seems to be with the door latch switch assembly, as the door was opened
forcefully due to overfilling of water so this indicates that it broke the door
latch and now it needs replacement. Please get back to me if you have any other
questions.
Kevin
Spin cycle makes jet airplane takeoff noise.
Bearings do exist but need a special puller to remove. If techs i n your
area have it part numbers are 22002934 , 22003441 also needed is
spacer 22002935 and seal kit 12002022 or else you need to order the
whole outer basket
Maytag Neptune washer is flashing a symbol that
Hi,
I believe you are describing a tS code.
If it is tS showing it
is an indication that the thermistor is shorted. The thermistor is the
temperature sensing device used on this dryer.
Before replacing the thermistor check for a clogged lint screen or dirty vent pipe.
If
these are clear and you are still getting the code the thermistor would
need replaced, the resistance of the thermistor should be about 10K
ohms at room temperature.
Note - Disconnecting the power supply for few minutes, say 45 minutes could resolve the problem temporarily.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
Not finding what you are looking for?