20 Most Recent Maytag MAH2400A Front Load Washer - Page 7 Questions & Answers


try putting in 2 caps of a citrus or pine bleech straight in to the drum with some old rags. then select a boil wash. the rags will spray the water around the tub, the bleech will clean the tub and make it smell fresh. DON'T put any clothing in whilst doing this. if you are worried about bleech in the machine just select a rinse cycle after. i do this once every 3 months

Maytag MAH2400A... | Answered on Aug 05, 2009


Hi, Some of the best information that I have found has been on YouTube. Go there, and type in "smelly washer" or "moldy washer". There are a number of good tutorials there.

Best regards, --W/D--

Maytag MAH2400A... | Answered on Aug 01, 2009


You have already analyzed the cause of the problem. That makes the fix much easier. Trace the hose that leaked by to your machine. There you will find that the hose is connected to a plastic solenoid valve. (A solenoid valve is merely an electrically powered diaphragm valve that is either open or closed). Disconnect the power to the washing machine. You can remove and disassemble the valve, getting down to the diaphragm and clean it, but for the time and cost, it will be probably easier and more effecient to replace the solenoid, and repair the other at your leisure. Any appliance parts supply house should be able to provide the part you need, at a low price.
Best regards, --W/D-- Please feel free to rate this solution!

Maytag MAH2400A... | Answered on Jul 29, 2009


take the plug/power lead for the machine OUT so machine no power then.

safety first.

you need to clean the filter and also may need to take the pump to clear it

Maytag MAH2400A... | Answered on Jul 25, 2009


Apparently there IS something wrong with the door switch. If you can, just jumper it out. Open the lid and get to the door switch. Tie the two wires together ans see if that cures it. That's it, try it!

If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Maytag MAH2400A... | Answered on Jul 20, 2009


Hi. your problem is actually a rather complicated one.

Timer and selector switches The timer switch is usually the largest dial on the main control panel. It can be either a mechanical device much like a simple clock, or completely electronic with just a digital readout.

The timer runs the washing machine in a pre-determined pattern. It provides the electricity to all of the washing machine components at the correct time and for the correct length of time.

The Start switch is usually part of the timer knob. When you set the timer to the proper cycle, you either pull or push the timer knob to start the cycle.

The selector switches or knobs vary from machine to machine. Most washing machines have one or several switches or knobs on the control panel besides the Timer/Start switch. These let you adjust certain settings; for example, the water temperature, spin speed, timer cycle, and so on. Normally, the washing machine completes the cycle selected on the timer, regardless of how you set these switches and knobs.

Maytag MAH2400A... | Answered on Jul 14, 2009


hello sir,
Please do the following checks 
  1. nspect the drain hose for kinks
  2. Test the timer control
  3. Test the lid switch (some models)
  4. Inspect the water pump
  5. Inspect the drive belt (belt drive only)
  6. Inspect the motor coupler
Click on the highlighted words for details on how to check. 

Maytag MAH2400A... | Answered on Jun 04, 2009


Sounds like the pump is going bad. It will drain while on the floor because the hose id lower then the water level inside the machine. You can get to the pump by removing the rear access panel. It is an electric motor. You can test to see if it is getting 120V.
They have been known for the impellor coming off the shaft as wel.
I hope this helps you. Please let me know if I can assist you further.

Thanks
Vic

Maytag MAH2400A... | Answered on May 25, 2009


If you have already replaced the main board then Its probably bad sensor. Have the sensors checked or have it replaced. I hope this helps. Have a good one.

Maytag MAH2400A... | Answered on May 16, 2009


likely a rubber gasket slipped off the groove.... try taking it apart and slipping the gasket back on.

heavy loads have more force during the spin cycle.

Maytag MAH2400A... | Answered on Apr 20, 2009


a cycle with just hot water and chlorine bleach will help but you may have to work at it a litle longer to get the door seal any cleaner in future run a short cycle with bleach and leave door open between use as much as possible..there is a new tablet shaped cleaner out now that may help in routine cleaning ckd with local dealer or repair personel also may ckd grocery shelf

Maytag MAH2400A... | Answered on Apr 19, 2009


Hi Pepsi,
"dc" means that the control board is trying to ramp up (that is, send a signal to the motor controller), but has encountered an unbalanced load and so shuts down. Specifically, "dc" means "distribute clothes".

I took this opportunity to upload a Tech and Troubleshooting manual for you. Here is the link for it. Read it carefully. You will be required to perform a "board output" test after placing the machine in "Service Mode".

I gotta tell ya, though. Based on my history with these, I highly suspect that the machine control board has failed. Let me know what you find, OK?

(And don't forget to rate this solution as "FixYA!", deal?

SG
9f7d68a.jpg

Maytag MAH2400A... | Answered on Apr 11, 2009


Check the drain hose. If it's not kinked or blocked then it could be the drain pump. I just pulled out two rocks from my drain pump. I found step-by-step instructions with pictures here:

http://blog.myspace.com/index.cfm?fuseaction=blog.view&friendID=58843118&blogID=364038999

Maytag MAH2400A... | Answered on Apr 01, 2009


remove 4 screws around edge of dispenser.remove dispenser cover front edge of dispenser is a nylon cord similar to weed eater string pull hard to left door should unlock .probably will need new lock but chance there may be just something stuck in pump might try getting to it by removing back panel from front remove screws each side of door frame panel will come off if you want to try from the front good luck

Maytag MAH2400A... | Answered on Mar 22, 2009


Disconnect the power. Keep the old board connected. Hold the new one next to the old one. Swap the wires ONE AT A TIME from the old board to the new board.

Maytag MAH2400A... | Answered on Feb 27, 2009


As for the user whose machine will not drain and sounds as though a chain is clanking, the solution is probably a coin caught in the drain pump. I just had the same problem. Access the pump from the bottom of the machine. 4 screws hold the mounting bracket on undo those, the electrical connection and two hose to the pump. Undo three screws holding impeller to motor and coin can fall out. Examine for damage if it is not too tore up, put back together. Keep in mind that when you unclamp the hoses that water will come out.

Maytag MAH2400A... | Answered on Feb 13, 2009


Some m/c's have a non return valve fitted at the pump end of the outlet hose, this wud prevent u blowing down it, u need to remove the hose completely from the pump to check for blockage.
Polz rate my solution.
Thanks.

Maytag MAH2400A... | Answered on Jan 24, 2009


You may need to remove the screws holding the top and slide is back a hair to get to thos screws holding the control panel.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Maytag MAH2400A... | Answered on Jan 02, 2009


no has to be completely dismantled unless you can get it out throw hose, call sears buy service smart agreement will cover up to 500.00, its a 2hr 2 man job to take apart and needs new center seal , a serve smart agreement is coverage on already broken appliance and 1 yr warranty that covers taking dryer off and on

Maytag MAH2400A... | Answered on Nov 14, 2008


sounds like you have a short in control board on washer buy service smart agreement from sears it will cost a little and cover up to 500.00 or give you 500.00 towards replacement value, dryer if you have heat its your vent in wall not breathing well , it will cause long dry times

Maytag MAH2400A... | Answered on Nov 14, 2008

Not finding what you are looking for?
Maytag MAH2400A Front Load Washer Logo

201 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Maytag Neptune MAH5500B Front Load Washer
Maytag Neptune MAH5500B Front Load Washer

2,929 Questions

Maytag Neptune FAV6800AW Top Load Washer
Maytag Neptune FAV6800AW Top Load Washer

1,479 Questions

Maytag Atlantis MAV6000 Top Load Washer
Maytag Atlantis MAV6000 Top Load Washer

921 Questions

Maytag PAV2300 Top Load Washer
Maytag PAV2300 Top Load Washer

670 Questions

Maytag EPIC MFW9700S Front Load Washer
Maytag EPIC MFW9700S Front Load Washer

642 Questions

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maytag Washing Machines

  • Maytag Washing Machines

Most Popular Question

maytag mah2400 bleach fabric softener

  • Washing Machines
Loading...