20 Most Recent Maytag LSE7806A Top Load Stacked Washer/Dryer - Page 9 Questions & Answers


It is most likely the tub seal. Take the two phillips head screws out of the front cover located low on the cover lift forward and remove. Set the machine two low level and fill with water only no soap or clothes when unit starts agitating look at the bottom center of the clothes tub if water is leaking here then you will need to replace the tub seal and tub bearing assembly.

Maytag LSE7806A... | Answered on Sep 13, 2010


check the water pump &hose

Maytag LSE7806A... | Answered on Aug 24, 2010


Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Maytag LSE7806A... | Answered on Aug 23, 2010


You can fix it yourself. Just call an appliance distributor and give them the model# and order a new timer. Good luck. Don't forget to rate me.

Maytag LSE7806A... | Answered on Aug 23, 2010


It should take a regular set of hoses for a washer they should all be the same.

Maytag LSE7806A... | Answered on Aug 16, 2010


Hi,

The symptoms you describe are consistent with a drive motor failing. The motor for the stacked units runs about $180.00 and would typically cost about another $150.00 labor for a reputable company to replace it.

Let me know if you have questions.

Maytag LSE7806A... | Answered on Aug 15, 2010


Hi.

If the lid switch is OK and there is water getting into the machine, then test and replace the pressure switch that detects water level.
Here the part:SUB 12002304 (Water Level Switch Kit)

Part is nr 6 in this diagram.

Also test the inlet valve to ensure that dual inlet is working. If hot is not filling, the machine will not complete filling.
A technician can swap valve contacts to find out if
both valves are opening.

If there is no filling at all, check the inlet valve and inlet duct:Water Inlet Valve.
Inlet valve is at the back of the appliance. It can be tested reading Ohms at terminals.



Maytag LSE7806A... | Answered on Aug 11, 2010


I would check heating element also on the heating element box is a thermostat probably need to check that also take the wires off the heating element and use an ohm meter to check it out it should register and not go to infinity. Same for the heating thermostat.

Maytag LSE7806A... | Answered on Jul 15, 2010


Overflowing can be caused by a faulty pressure switch or tube from switch to the tub. It is operated by air pressure from water filling in the tub. If this does not activate then the inlet valve will continue to allow water to enter the machine. If it is overflowing during spin only it is most likely something obstructing the pump. If it is filling the tub even when the machine is off the problem is the inlet valve.

Maytag LSE7806A... | Answered on Jun 28, 2010


The problem is the water inlet valve has failed. This is inexpensive and easy to replace. Here is your part # AP4026989 If you need help installing try this link http://appliancehelponline.com/topload.html
all parts come with installation instructions. You can also enter your model # for diagrams and illustrations

Maytag LSE7806A... | Answered on Jun 15, 2010


OK it may be one of 2 things. I would check the lid switch first. On some maytags the have a lid switch that if it is not working properly it will not let the washer fill. If it will not fill the washer will not wash because the pressure switch did not activate the timer to wash. If the switch checks good you might have a bad timer. If you open the control panel you will find a tech sheet with the wiring diagram. I would follow the fill cycle and check the components. You might also check the water valve to make sure its ok too. But its very rear that both the hot and cold would go at the same time. Good luck!

Maytag LSE7806A... | Answered on Jun 08, 2010


Are you putting clothes in first or as you fill the machine??? This is a normal capacity washer, so you need to be sure to fill with clothes first, I believe this will cure it. If that isn't your trouble, you may have a level switch that isn't working correctly. That would be easy enough to fix. Check on High, Med and Low levels and see how much water goes in, if it looks high on any of them, you can use that leveling screw on the level switch itself to regulate how high or low it goes. UNPLUG the machine when inside, so you don't shock yourself, Make your adjustment, then replug and try before you reassemble the machine. Unplug for that too, just to be safe. :) let me know how it works out for you

Maytag LSE7806A... | Answered on Jun 04, 2010


Your door switch maybe faulty, http://www.servicematters.com/maytag_library/docs/16000416.pdf
There is your service and repair manual, use the troubleshooting steps to isolate and repair your issue. http://www.washerhelp.co.uk/diy-repair-help.html

Maytag LSE7806A... | Answered on Jun 01, 2010


Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine2_bing.gif does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine2_bing.gif then checkout this tip...

Front Load Washing Machine2_bing.gif not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Maytag LSE7806A... | Answered on May 22, 2010


Without the model number this is just a guess but some of the maytag stacks have a fuse for the washer. Remove the 2 screws at the bottom of the front panel for the washer and look along the left front side where the water level switch is and you may see a fuse there. If there is one this fuse is probably blown.

Maytag LSE7806A... | Answered on May 19, 2010


It sounds like the lid switch is not activated when the lid is closed. The lid switch is where the power to the drive motor is routed and its failure disables the motor. Check if you can hear the motor hums indicating that it is running when the lid is closed. The lid switch is indeed not working if the motor is running; otherwise, the belt is either broken or has slipped off the pulley if the washer is belt drive or the motor coupler is broken. Please specify the exact model number of the washer for specific and accurate troubleshooting and repair advice

Maytag LSE7806A... | Answered on May 11, 2010


Maytag Top Load Washers are equipped with Unbalance Control System that monitors the washer for vibration and unbalanced condition. It consists of outer tub displacement switch, inertial switch, strut displacement switch, and a cabinet vibration sensor mounted on the control board. One of the switches may have been dislodge causing the washer not to start again. Please indicate the exact model number of the machine for specific and accurate troubleshooting and repair advice.

Maytag LSE7806A... | Answered on May 10, 2010

Not finding what you are looking for?
Maytag LSE7806A Top Load Stacked Washer/Dryer Logo

434 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

606 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maytag Washing Machines

  • Maytag Washing Machines

Most Popular Question

model lse7806ace maytag stackable

  • Washing Machines
Loading...