20 Most Recent
Panasonic TH-50PX60U 50 in. Plasma HDTV - Page 4 Questions & Answers
My panasonic th-50px60u television turned itself
Tries tv unplug,replug it back like about an hour later for the tv to do it resetting itself back to the factory setting,tv might work again.If not still same problems.The tv 90-95% it is the board that call the tv power supply board is having a problems.That the board where the tv power a/c cord plug into it.U have all tools and know basic electronic and also can do basic soldering works too?Yes,take the tv aparts,check the tv power supply board carefully for dying and soon to be dead capacitors components parts.These capacitors components parts are alway bulges up or puffing up onto it tops.These dying and soon to be dead capacitors components parts are bulges or puffing ups on to it tops must have to be replaced will solved ur tv power unstable and flashing red light.Or try website like Ebay.com to buy a whole new refurbish tv power supply board for the replacement.
7/29/2011 11:19:19 PM •
Panasonic...
•
Answered
on Jul 29, 2011
I have 42in plasma tv.
Hi,
Please let me know if the symptoms also appear in all inputs like when you are watching movie on the DVD player?
Jdvillanueva
7/5/2011 10:08:45 PM •
Panasonic...
•
Answered
on Jul 05, 2011
The picture on my panasonic
First try reseating both ends of the LVDS cable.
By "reseating" that basically means unplugging, and re-plugging them in their slots right?
fixed
a few monitors similar to that by replacing a few bad caps. Look for
swollen caps. Sometimes the tops of them will have a bulge or a split.
It might be better to just replace them all.
Look on the Power supply board for Bad Capacitors they will be vented or puffed up on Top.
This board will be on the Far Left hand side,pull it out and look for bad Caps.
You need to know how to Solder with an solder Iron, unsolder bad caps and replace with new .
Make
sure you put them back in the exact same way the came out,they will be
marked positive side and Negative - Side. If they are 1,000uf 16v make
sure the cap is 1,000uf. If you want to just replace the board, here are
some company's for Parts Encompass Parts Distribution 1-800-638-3328
Visit their Website they will list Parts /Prices they also have Free
Service Manual that you can printed out.Parts 1-800-627-4368 PTS
1-800-844-7871 this company you can ship your boards to and have them
repaired. Let me know if you need any more help.
6/23/2011 9:43:42 AM •
Panasonic...
•
Answered
on Jun 23, 2011
I have a Pansonic TH-50PX60u.
This problems are the 2 Buffer boards X or Z is dead.Sorry must hire a tv to troubleshoot and change the wright one.Could be etheir one or both.
1/15/2011 2:39:40 AM •
Panasonic...
•
Answered
on Jan 15, 2011
I have a panasonic TH50PX60U.
The tuner (the part on the tv that selects the channels and extract the signal from them) or the image processor is defective. Since you can see dvd's the first option is way more plausible.
The tuner is a relatively cheap part ($75) but it's very complicated to install and remove so the labor will be very expensive($200). If you're unlucky you will have to replace y the entire mainboard for a cost of about $550.
http://www.partstore.com/Part/Matsushita/Panasonic/TH50PX60U/Matsushita/Panasonic/TNAG167S/New.aspx
12/20/2010 3:59:41 PM •
Panasonic...
•
Answered
on Dec 20, 2010
Top left corner of screen completly black
hi,
i think ur tvs closed caption option is ON. make it of by the following procedure .
1.press menu and select setup
2. in the setup menu select cc.
3.in the cc menu select mode and change it to off.
4. then press ok. exit menu and and watch the corner.
if nothing happened ,
do the above mensioned first two setup and
3. in the cc menu select cc reset and then press ok
ok,
12/17/2010 6:57:44 PM •
Panasonic...
•
Answered
on Dec 17, 2010
I have a Panasonic Plasma that the wife used
Go to walmart and the sale a 3 wheel 5 chalk polishing kit. Attach a wheel to a drill and use the white chalk to buff the screen. it works on glass, aluminum, plastic, and pretty much anything smooth or pourus and only cost about 10 bucks.
GOOD LUCK AND PLS RATE THIS POST!!!
6/5/2010 9:38:56 AM •
Panasonic...
•
Answered
on Jun 05, 2010
The TV will not come
Ten blinks means one of the following:
10 blinks:
Sub 5v SOS / Main 3v SOS DG Board / DTV 9v SOS / Tuner Power SOS: faulty digital board or faulty power board /Faulty digital board detecting wrong voltage to tuner board or faulty power board.
You can try leaving the TV unplugged from power for one hour or so, this will clear the error if it was a false alarm.
If that does not fix the problem, then the TV must be tested and repaired.
If you need repair service you can contact the number listed on the owner manual.
5/23/2010 4:59:18 PM •
Panasonic...
•
Answered
on May 23, 2010
I have a service manual,
Hi
Thanks
for using FixYa. A plasma TV is a very hard working device. It is
working harder than any TV that has been built before, and as a result it
produces a lot of heat. 75% of technical problems in plasma TV's are caused by
overheating problems. X, Y sustain, buffer boards controls
picture, fires the gas, and many others functions. When either of these boards goes
bad common problems include negative image, no image, vertical or horizontal
stripes on picture, turns on and than turns off, and many more. You’ll need to
open the back off the TV and check for any swollen/bulged/leaky capacitors on these
boards and replace whichever has gone bad. All this is only recommended if you
have electrical expertise & know how to solder/re-solder components as these
units contain high voltages even when switched off.
Please do
accept the solution if the issue is resolved or else revert for further
assistance.
Thanks
Rylee
2/5/2010 4:41:18 AM •
Panasonic...
•
Answered
on Feb 05, 2010
Samsung 50 in. HPS5033X/XAA colored lines
How wide are the lines. Do they change width? Where on the screen are they located?Connections on the c boards at the bottom to the panel flex cables or bad c board itself can cause 2 inch wide verticle bar. Before touching these connectors be sure power supply is disconnected from the 2 sustain boards on the sides. If you don't there will be an arc that will destroy the flex cable thus you will have to replace the panel. If C boards or connections don't fix it the replace the plasma panel. If the lines are thin lines then panel is likely bad. Contact Panasonic even if out of warr they may help.
1/19/2010 8:42:00 PM •
Panasonic...
•
Answered
on Jan 19, 2010
Have 4 yr old plasma
The firmware is not the issue because the power button is working rather its the control module under the buttons that has failed and saying that so did the SD card reader as a given fact as it did not take the firmware. I would seek local qualified repair tech to replaced said board you be glad you did,
please take the
opportunity to rate my solution and press the accept button for my expert advice and efforts. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/edwy_1a56970cf1ea4620
1/6/2010 5:06:22 PM •
Panasonic...
•
Answered
on Jan 06, 2010
Not finding what you are looking for?