Panasonic PT-52LCX65 44" HDTV - Answered Questions & Fixed issues
Just replaced our blub in
jlamina19,
You could have a bad optical engine, but first try this tip. Remove the lamp assembly again and make absolutely certain that everything is inserted and seated correctly. If this does not help you may have damaged your optical engine when the lamp quit. They can get very hot before failure and this could have damaged one of the TFT panels. I have a tip to explain how to change the engine at
http://www.fixya.com/support/r4251975-replace_dlp_light_engine.
Thanks for using FixYa and for the great rating.
hardrocko
9/15/2014 9:49:57 PM •
Panasonic...
•
Answered
on Sep 15, 2014
•
123 views
TV won't power on
Sounds like the bulb is not firing. I have the 44 inch model. Like it too. It is normal for the power indicator to blink for a minute or two AFTER the set has been turned off from running. get a phillips or panasonic TY-LA1000 bulb or a P22H 120 watt one if you can remove the old one from the housing (not very hard to do).
5/8/2014 8:21:06 PM •
Panasonic...
•
Answered
on May 08, 2014
•
76 views
How to reset lamp timer on panosonic PT56DLX75
NOTE: If the "Please Replace Lamp" message is displayed, press [RETURN] or [EXIT] on the remote to remove the message. 1. Turn the unit ON. 2. While pressing the [VOL-] button on the unit, hold down the [SPLIT] button on the remote at the same time for more than 5 seconds. 3. When the reset procedure is completed, the following message is displayed on the screen: "LAMP TIME WAS RESET TO 0".
3/11/2014 3:39:26 PM •
Panasonic...
•
Answered
on Mar 11, 2014
•
166 views
I have panasonic pt52lcx65 it kept saying to
Howdy,
YES, the TV was telling/warning you that Lamp was going out soon so you would not be without the use of your TV while you get a Lamp.
Thanks for using FIXYA, BIG IRISH.
4/28/2013 3:16:14 AM •
Panasonic...
•
Answered
on Apr 28, 2013
•
236 views
How to reset lamp timer on panasonic pt-52lcx16
Turn On tv, press and hold Volume Down button on TV Front and Play/Split button on Remote at same time for six seconds to reset lamp timer.
TV screen will show lamp timer reset display upon successful process.
12/3/2012 2:26:14 PM •
Panasonic...
•
Answered
on Dec 03, 2012
•
1,900 views
How to fix the optical engine
Usually they cannot be "fixed" but are exchanged and rebuilding takes place in a controlled environment---seen several techs take them apart and end up having to replace the entire unit anyway.Some of these Panasonic sets only sell the chassis and no parts.
5/21/2012 1:52:38 PM •
Panasonic...
•
Answered
on May 21, 2012
•
40 views
PT-52LCX65 Lamp Meter
Hello.. meseta809
first off all it's not necessary to have the TV on to reset it. the problem is the dmd need to send the info that you have a working lamp.
try this to see if it work's
Panasonic TY-LA1000 TV Lamp Reset Procedure/instructions:
Ok,
so apparently there are a couple of different ways forum members have
found out how to reset their Panasonic Lamp timer (this should apply to
all of them, not just the TY-LA1000 specific lamp)
“Hold the VOL down button on the TV and the SPLIT button on the REMOTE for five seconds”
Again,
you will need to press the Volume button on the TV while pressing hte
SPLIT button on the Remote Control for five seconds, it will NOT work
if you try to do it both from your remote!
5/16/2012 5:19:38 PM •
Panasonic...
•
Answered
on May 16, 2012
•
848 views
Repair on problem blue dot
Good Day, flavrlen;
This is your fix it is not costly and if you handle a screwdriver you can do this in 30 minutes:
PANASONIC:
MODELS: PT-44LCX65, PT52LCX15, PT-52LCX65, PT-52LCX35, PT-61LCX65,
PT-61LCX35.
SYMPTOMS: 1. FUZZY SPOTS
2. FUZZY SPOTS
3. FUZZY SPOTS WITH STAINS
4. FUZZY SPOTS & UPSIDE DOWN
5. FUZZY SPOTS WITH LINES
CORRECTION: SYMPTOMS CAN BE CORRECTED BY EEPROM
CORRECTION TOOL; (LSUQ0100).
Good Luck, big IRISH.
11/10/2013 4:39:35 PM •
Panasonic...
•
Answered
on Nov 10, 2013
•
1,339 views
I get a message to
hi, To clan the air filter you have to remove the projection unit.You can see the projection unit behind the lamp blast board.There are three air filters in this unit. You have to clean these air filters. I have added the picture which showa the location of air filters. If you can give your email address the i will sent the service manual. Which will help you to remove and clean these Air filters. Remember one thing remove lamp first then only remove the projection unit from the rear side. OK
10/10/2011 8:51:43 AM •
Panasonic...
•
Answered
on Oct 10, 2011
•
517 views
How do I know the model of my projection panasonic
All sets made by Panasonic and others have a label on the back with model number, serial number and date made. The serial number only is used for non technical purposes.If you have a problem be sure to post the model number so I or another expert can give you help.regards, sd tech
9/29/2011 6:52:07 PM •
Panasonic...
•
Answered
on Sep 29, 2011
•
207 views
Not finding what you are looking for?