Top 20 Kyocera FS-1028MFP Mono Multifunction Laser Printer Questions & Answers

empty drum unit its full of waste toner each side of drum unit has plastic covers that pop off empty out the unit thoroughly and vacuum inside

usally the speed of the machine with two zeros or try Admin or Admin00

u130 dev unit set up and u251 clear main count

Video help in the links https://www.google.com/search?q=Kyocera+M2040DN+Laser+MFP+Printer.+How+to+change+the+HVT+board ..

https://fixing-tech.com/fix-c2730-error-on-kyocera-taskalfa-4551ci/

The error code C3800 on a Kyocera 3212i printer indicates an AFE error. This error occurs when writing data and reading data does not match 3 times continuously, or there is no response from AFE for 100ms. The following steps can be taken to resolve this issue: Check the connection FFC is not connected properly. Or it is faulty. Clean the FFC terminals of the following FFC and reconnect them. If the issue persists, consider contacting a Kyocera technician or service provider for further assistance.

I would check the connection to the main board as a backup error code can be caused by intermittant connectors.

Question edited for a lot more clarity. Question moved to Kyocera. Nothing to do with a fax card, just make sure the back door is closed. It is normally called the 'Bypass Door' and gives card stock a flat run.

Kyocera FS-2026MFP "Toner Cartridge Improperly Installed"

Copytechnet https://www.copytechnet.com > kyocera-mita-copystar May 26, 2020 - I have tried multiple things and the error message is still there. 1.) tried new toner cartridges. 2.) made sure toner waste basket was ... Thread: 3552CI The toner container is not properly installed Aug 1, 2020 Kyocera M6526CDN Error F375 & F246 & (Y) Toner ... Sep 28, 2021 FS-6025 toner container not installed - Copytechnet Nov 18, 2012 Kyocera ECOSYS M3655idn - Waste Toner Bottle Not Installed Feb 21, 2022 More results from www.copytechnet.com ..

Check Network Connection: Ensure both devices are on the same network.
Restart Devices: Power cycle both computer and printer.
Verify Scanner Settings: Confirm correct scanner selection.
Update Drivers: Install latest printer drivers.
Firmware Update: Consider updating printer firmware.
Inspect Cables: Check all connections.
Contact Kyocera Support: If issue persists, reach out to Kyocera's support.

See Appendix A (Page 245) and Appendix B (Page 250) of user manual for help. Appendix A Error Codes - Kyocera KM-1650 Operation Manual [Page 245] ' ManualsLib See Service Manual for further help 2FT ver3 KMA_E.book (manualslib.com)

See troubleshooting section (Chapter 10) of user manual for help. Kyocera-ECOSYS-M5521cdw-Operation-Guide-DSBLS.pdf

Google suggests the following for same error How to guides for KYOCERA Devices - 3101 (google.com)

See the error code list in troubleshooting section Error Code List - Kyocera FAX System 10 Operation Manual [Page 212] ' ManualsLib For further reference see troubleshooting 10 Troubleshooting - Kyocera TASKalfa 4002i Operation Manual [Page 501] ' ManualsLib All the relevant manuals are here Product Support & Downloads ' Kyocera (kyoceradocumentsolutions.co.uk)

Presumably you mean the WASTE toner container. https://www.google.com/search?q=Kyocera+3511i+it+says+check+toner+container ..

Thermister failure or too much heat.

Kyocera TASKalfa 1800 - Error Code

Printcopy.info https://printcopy.info > model=TASKalfa 1800 Code: 6020; Description: Abnormally high fuser thermistor 2 temperature (Center) Fuser thermistor 2 detects a temperature higher than 210°C/410°F. More help and videos https://www.google.com/search?q=Kyocera+taskalfa+1800+showing+c6020 ..

If your Kyocera KM 3050 printer is displaying "toner empty" message, even though you have replaced the toner cartridge with a new one, it's possible that the toner sensor inside the printer is malfunctioning or is dirty. You can try the following steps to fix the problem:

1. Open the front cover of the printer and remove the toner cartridge.

2. Look inside the printer, and you should see a small sensor that detects the toner level. This sensor may be dirty or covered with toner particles.

3. Clean the sensor with a soft, dry cloth and reinsert the toner cartridge into the printer.

4. Close the front cover and power on the printer.

If the problem persists, try resetting the printer's toner counter. Here is how to do it:

1. Press the "System Menu" button on your printer.

2. Scroll down to "Service" and press the "Enter" button.

3. Scroll down to "Maintenance" and press the "Enter" button.

4. Scroll down to "Reset Toner Counter" and select it.

5. Restart the printer and check if the problem has been resolved.

If none of these steps work, there might be a more serious hardware issue with your printer's toner sensor, and it's advisable to contact a Kyocera printer support expert or service center for assistance.

Download the operation guide and see section 5 (Troubleshooting). It may help. Product Support & Downloads ' Kyocera (kyoceradocumentsolutions.eu)

If your Kyocera Ecosystem P3045dn printer is producing vertical marks on printed sheets, there could be a few potential causes for this issue. Here are some troubleshooting steps you can take:

1. Check the print cartridge: Inspect the print cartridge for any damage or defects. Ensure that it is installed correctly and securely in the printer. If the cartridge is low on toner or nearing its end of life, replace it with a new one.
2. Clean the print head: The print head may have accumulated dirt, debris, or dried ink, which can cause vertical marks on the printed sheets. Refer to the printer's user manual for instructions on how to clean the print head properly. Use a lint-free cloth or recommended cleaning materials provided by the printer manufacturer.
3. Check the drum unit: The drum unit could be dirty or damaged, leading to the production of vertical marks. Remove the drum unit according to the printer's instructions and inspect it for any signs of damage or wear. Clean the drum unit using a soft, lint-free cloth. If the drum is damaged, consider replacing it.
4. Inspect the paper path: Check the paper path for any obstructions or debris that might be causing the vertical marks. Look for torn or wrinkled paper, as it can leave residues on the print path. Remove any obstructions and ensure the paper is loaded properly in the tray.
5. Adjust print settings: Ensure that the print settings in your computer or printer driver are correctly configured for the paper type and print quality. Adjust the print density or quality settings to see if it affects the appearance of the vertical marks. You may need to experiment with different settings to achieve the desired result.
6. Update printer firmware and drivers: Outdated printer firmware or drivers can sometimes cause printing issues. Visit the Kyocera website and download the latest firmware and drivers for your printer model. Install the updates according to the provided instructions.

It sounds like your paper is set to Letter size and you are printing onto A4 size paper? That would result in a 4 cm gap difference. The engineer says the printer is okay, so the problem must be deep in settings of the device sending the prints to the printer. You are famous! https://www.google.com/search?q=KYOCERA+TASKalfa+352ci+leaves+4+cm+gaps ..