20 Most Recent HP LaserJet 3600n Printer - Page 5 Questions & Answers

There is a communication interrupt between Dc controller & formatter, remove and re connect all the flat cables which was connected to DC controller.. check if its not resolved replace DC controller.

Disconnect power cord, pull out formatter & refix back add little bit force, give power then check,

Hi valfreestone,

^ ^, Find your driver you can check it out here just click the download button corresponds to the driver. The system i choose here is Microsoft Windows Xp,

Hp LaserJet 3600n Printer Driver

If that's now your system message me here and ill assist you again ^ ^, in changing the system for the appropriate driver.


Hope this helps ^ ^,

Webby101

Hello,

remove toner, shake and very well, then try again....

Let me know if this doesn't help.

Regards.

Its a particular problem with this printer, it needs a firmware update.

http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesId=501044&swItem=lj-44336-1&prodNameId=501046&swEnvOID=54&swLang=8&taskId=135&mode=4&idx=1

You take your chances with refilled cartridges. The only way that I know to fix your problem is to use HP cartridges, new ones...not refilled.

Hello ,
This is due to failure of your fuser unit ,Replace them with new one yor problem will be resolved 100%.

Could be a broken "cartridge lock" or a bad "cartridge drive motor". Someone is going to have to look at it.

Problem with the yellow cartridge. Try reseating it

Hi

Check for the correct installation of the paper tray. Most likely the pickup and feed rollers are worn. These are held in by little embedded plastic clips. There are rollers in the tray itself. To remove the rollers in the tray there's a little plastic door on the tray. Lift it up, then depress the plastic clips on the side of the roller and slide it off. The other rollers are inside the printer just about the tray on the right.

You need to order roller kit online.

Please get back to us if you have further query else please accept the suggestion.
Thank you for contacting fixya.com

Low fuser temperature. Could be bad fuser or a bad DC Controller. Fuser is cheaper and easier to change, start there.

10.92.00 The Black print cartridge are not engaged correctly.

? Open and then close the front door.
? If the message persists, make sure all the print cartridges are seated correctly.
? Clean the contacts on the memorycontroller PCA.
? Make sure that connectors J302, J303, J304, and J305 on the memorycontroller PCA are seated correctly. Also make sure that connector J1020 on the DC controller is seated correctly.
? Replace the memory-controller PCA if it is damaged.
? Check the gears on the print-cartridge drive motors. Replace defective motors.
? Replace the DC controller.

Welcome to Fixya

Normally, you will need to use soap and warm water to see how much of it you can get off. Make sure that you don not put soap into the printer mechanism. If you already tried regular soap, step up a notch and purchase some lava soap. It's commonly known as black soap and is made by WD-40. What sets this soap apart from regular soap is that it's made with ground pumice, which is material that comes from lava. With this added ingredient, it usually gets ink right off.

Another common household item that can be used to clean off ink (either on your hands or on other surfaces) is common hairspray. Simply spray it on the area of ink and let sit for 6-10 seconds. Then wash with soap and warm water.

Thank you for using Fixya! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

How does the inside of the printer look? If it is very dirty, then it is possible that the laser scanners are polluted. The other possiblity is that one bad cartridge can cause all colors to print poorly due to the fact that all the high voltage is driven off one board on these printers. If you recently installed a new cartridge, try swapping it out for the old one, if the print quality improves, you have a bad cartridge for sure and should have the store you bought it from replace it.

need to replace formatter board

Kindly check the printer settings and preferences. Maybe it was set to grayscale, afterwards, try to do a print alignment and last resort is check toner if it's clean. Try to wipe with paper towel and do the printer test. Hope it may fix your problem :)

Replace it for a new cartridges. If continues the problem check the laser, clean it.

Hi Do the following and good luck. You may have to sen away for parts.


So, please perform the following steps to isolate the issue to its exact cause:

1. Power is an important part of LaserJet printing and inadequate or marginal power supply can cause this sort of issue to occur. Please plug the printer directly into a wall outlet to eliminate the possibility of power issues caused by other power devices.
2. Then, remove the black cartridge and clean the E-label as well as the metallic toner contacts at the cartridge ends using a dry linen cloth. Then reinsert the cartridge.

3. Then, please perform a cold reset on the printer. A cold reset clears all data from the printer memory and sets all the defaults back to the factory settings.

CAUTION: Performing a cold reset resets the Jetdirect configuration. To avoid making changes to the network configuration, remove the HP Jetdirect print server before performing a cold reset.

NOTE: If possible, print a configuration page and menu map prior to performing a cold reset. This will document the current settings for later reference.

Perform a cold reset from the printer as follows:

a. Turn the printer on.

b. Watch the control panel.

c. When the memory starts counting, press and hold the green (Select) button. Continue to hold Select button until all three Control Panel LED's are illuminated and on solid.

d. Release the (Select) button.

e. The control panel will display SELECT LANGUAGE.

f. Press (Down Arrow) button until control panel displays COLD RESET.

g. Press (Select). The printer will perform a cold reset and then continue its power-on sequence.