HP LaserJet 3600n Printer - Answered Questions & Fixed issues
Default password for HP Laserjet
by default an HP printer does not have an administrator password installed. if the printer asks for a password, this means that someone has installed it and only that person knows the password.
1/7/2019 7:30:36 AM •
HP LaserJet...
•
Answered
on Jan 07, 2019
•
11,450 views
Door closes with no cartridges but will not with
Did you make sure the cartridges clicks in place? There are while plastic locks on each cartridge and hopefully they are not broken. Not expensive to purchase but major teardown to replace.
1/31/2015 3:46:19 PM •
HP LaserJet...
•
Answered
on Jan 31, 2015
•
87 views
HP3600 USB printer works but won't print on my HP7058 Laptop
Try removing all ports from your laptop, then reboot, and then create just one USB port. Also, go to your hardware devices and make sure your usb ports don't have any question marks or yellow warning symbols. Be sure first that the drivers for your USB ports are installed and working first. This sounds either a faulty USB cord, which does happen, or USB drivers issues in your laptop. The printer is probably not the problem here.
1/5/2015 9:40:36 PM •
HP LaserJet...
•
Answered
on Jan 05, 2015
•
394 views
How to remove side panel hp 3600
To remove the side cover: Open the fuser cover and remove the fuser. There are four screws that hold the top cover on, remove those and lift the top off, watching for the connector wire on the right side. Remove the formatter. On the bottom of each side panel, where the lift handle is, there will be 1 screw, remove the one for the side you want to remove. If you want to remove the left panel there is also a screw on the lower back of that panel. The right panel only has the one screw. If you go to feedroller.com you should be able to download the service manual that will give you detailed instructions and pictures.
8/16/2014 5:37:28 AM •
HP LaserJet...
•
Answered
on Aug 16, 2014
•
823 views
What initializing take to long
These printers take to long to be ready because these printer first get heat up and check every section and then get ready.
7/30/2014 6:42:08 PM •
HP LaserJet...
•
Answered
on Jul 30, 2014
•
49 views
How to cold reset
http://www.ehow.com/how_8337650_do-restart-color-laserjet-3600n.html
Instructions
<:section>
-
- 1
Turn the printer on and look for the control panel display to count the memory. When the memory count begins press and hold the green "select" button located on the front of the printer. When all three of the front control panels LED are lit release the "select" button.
- 2
Press the "Down Arrow" once when you see the "Select Language" display. Press the "Select" button until your control displays "Cold Reset."
- 3
Press the "Select" button and your printer will initialize a cold reset.
7/1/2014 7:31:48 PM •
HP LaserJet...
•
Answered
on Jul 01, 2014
•
167 views
Replace and reset fuser for hp 3600
I tried the reset fuser and your instructions do not work for the 3600n. reset supplies is under another category and new fuser kit is not an option?????
2/6/2014 1:40:48 PM •
HP LaserJet...
•
Answered
on Feb 06, 2014
•
2,526 views
Cpr sensor out of range. Calibrating takes long. How can it be resolved?
immediatly below the fuser unit/ above the image transfer belt inside the covers are the colour calibration sensors- they have mylar windows which get coated over time- clean with isopropyl- the sensors are looking vertically down and are approx 5x15mm is size there is one sensor to the left and one to the right, if after cleaning these the error still exists- try replacing the ITB and try again
1/30/2014 12:40:15 PM •
HP LaserJet...
•
Answered
on Jan 30, 2014
•
1,237 views
59 co error
59.xx error main motor failed to reach rotation speed in a given time:-
have you recently changed a toner cartridge? is it 3rd party?
remove all toner cartridges and then switch power on to printer - it should turn over then ask for toners to be inserted, if so the problem probably lies with a toner cartridge
if the toners prove to be ok then the issue may be the Developer lift plates ( front/rear) which tend to snap after a while not an expensive repair but time consuming..fuser units on this machine dont generally give main motor failures neither does the transfer belt. If I was attending this call I would definatly have a full set of spare toners and the dev lift plates to hand as this would most likely be the fix
1/17/2014 1:32:44 PM •
HP LaserJet...
•
Answered
on Jan 17, 2014
•
184 views
Cartrage not engaged
Try to follow the instructions in a user's manual:http://www.retrevo.com/support/HP-3600n-Printers-manual/id/313ag619/t/2/www.hp.com/support/cij3600
1/24/2013 2:03:26 AM •
HP LaserJet...
•
Answered
on Jan 24, 2013
•
50 views
Not finding what you are looking for?