Epson Stylus CX3810 All-In-One InkJet Printer - Answered Questions & Fixed issues
Pulling in multiple pages at once
Epson makes a pickup and, roller assembly for your printer as these wear out after a while and, stick. any office supply can order it for you.
1/16/2018 5:22:54 AM •
Epson Stylus...
•
Answered
on Jan 16, 2018
•
55 views
Windows 8.1 print color wrong
Please replace the cartridges and see if that does the trick, if not. then try uninstalling and re-installing the printer
5/11/2014 8:53:42 PM •
Epson Stylus...
•
Answered
on May 11, 2014
•
45 views
WILL ONLY PRINT EVERY ALTERNATE LINE OF TEXT & TEXT BOX BORDERS
Doesn't sound like your printer hardware. Try printing something other than your text document. If the page comes out clean/perfect then it means your printer is having a problem understanding your text document via print program translation. Otherwise try converting your text to pdf and print a sample page, if it works then again problem with software/printer translation.
11/24/2013 7:17:47 PM •
Epson Stylus...
•
Answered
on Nov 24, 2013
•
346 views
After I changed my ink cartridge when I try to
Hi there,
Did you use a replacement ink cartridge or is it an original Epson cartridge? The only way that it will do this is if the cartridge is not seated properly or cartridge that you installed is intended for another model.
Try to reseat and review your cartridge model. Post your observations here.
9/10/2011 5:20:41 PM •
Epson Stylus...
•
Answered
on Sep 10, 2011
•
58 views
I bought new ink cartridges
turn off your printer..plug out your printer power cable from the printer the plug in the cable power together with pushing the start and reset button, hold on for about 5 second
5/7/2011 10:23:23 AM •
Epson Stylus...
•
Answered
on May 07, 2011
•
54 views
Printer is printing each color
sounds like the print head is malfunctioning. try running the head cleaner a few times from the settings menu, if that doesn't solve it you'll have to replace the entire head, at which point it may be more worthwhile to replace the printer.
3/15/2011 10:39:51 PM •
Epson Stylus...
•
Answered
on Mar 15, 2011
•
47 views
In my all in one
The printer thinks that you have a paper"clogged" when the rolls that move the paper rotate with difficulty. So either there's something in there that is blocking the rolls or the plastic bearings on which the rolls turn are seized by dirt.
To fix both of that you will have to dismantle the printer: the plastic case ill have to be detached from the body. It's quite complicated, removing some screws and popping some tabs without doing any other damage will be difficult if you haven't done that before so try to find a shop that would do it on the cheap. Otherwise you will have to try to dismantle it yourself - you have nothing to lose if you damage it, it dead as it is now anyway.
12/6/2010 8:13:20 AM •
Epson Stylus...
•
Answered
on Dec 06, 2010
•
32 views
Epson stylus cx3810 printer paper jam
I had a small piece of plastic get jammed in the mechanism that loads the paper, it is a pretty simple fix as long as you are careful about organizing parts as you remove them.
Step 1: remove the small plastic panel where the usb connects, this exposes all the wiring for the scanner, you will need to carefully remove 2 plastic connectors each with four or five wire, then remove the ribbon cable from the slot. There is a screw in a clamp that holds it tight, loosen that and make sure all the wires are clear. Moving that ribbon cable will expose a screw holding the scanner on, remove that screw, then look at the other hinge, remove the screw on top and the scanner assembly should just slide off, be mindful of the wires while you do this.
Step 2: remove the control pannel, slide the control pannel towards the back of printer, it should just slide out, disconnect the ribbon cable and set it aside.
Step 3: Remove all the screws from the top cowl, should be seven screws total, i just leave them in the deep slots and keep the piece level as I remove it. That should give you access to the internals to remove anything that was jammed in the printer.
Note: Any time I do a project like this I always make sure to lay out all my screw visually in the same way they came out, since there are several different kinds of screws. Just follow the process in reverse to reassemble, making sure you reconnect all the ribbon cables and wire connectors.
11/30/2010 7:12:41 PM •
Epson Stylus...
•
Answered
on Nov 30, 2010
•
946 views
Where can I find a free copy of the manual to
Unless you get someone who owns one in PDF format to send it for FREE, you will probably have to buy it- sorry- prices vary but I buy a lot of manuals from www.2manuals.com- will probably cost about $10
6/1/2010 6:50:05 PM •
Epson Stylus...
•
Answered
on Jun 01, 2010
•
197 views
Not finding what you are looking for?