20 Most Recent Motorola Mobility H500 Wireless Headset - Page 10 Questions & Answers


Try to reset the unit with the phone again.

Motorola... | Answered on Apr 02, 2009


my headset works fine if I get a incoming call.When I dial out no one can hear me.

Motorola... | Answered on Apr 01, 2009


send them as a oicture message to your email address

Motorola... | Answered on Mar 28, 2009


1.Press and hold the Multifunction button in the middle of a boom headset while the headset is closed. The light will glow blue.
2.Open the boom microphone and the blue light should remain on. If not, repeat step 1.
3.On the cell phone, press Menu > Settings > Connection > Bluetooth > Handsfree > New Device
4.Select H500 once a connection is detected.
5.The passkey "0000" is now entered to confirm the connection has been made.
6.The cell phone screen will now read "Bluetooth Connection".

Tips:
1.Provided you set the Bluetooth power to "On" after the initial connection has been made, the phone will automatically re-connect to the headset.
2.To set the Bluetooth power on - Press Menu, Select Settings, then Connections, then Bluetooth link, scroll to Setup and select that. Scroll to Power and chose Change. Scroll to On and press Select. The screen should now read "Changed: Power On".
3.Test Your Connection: Close the headset and watch for cell phone to say "Disconnected". Re-open the headset and the phone should be connected automatically and will now display "Bluetooth Connected".

please give good rating if the solution works.
Thanks for using FixYa.

Motorola... | Answered on Mar 28, 2009


try pass code 0000 it's a default code thats comes with it.

Motorola... | Answered on Mar 25, 2009


you hold down the button untl the blue light stays on steady and then make your phone search for available bluetooths in range, and then when it asks for a code enter four zeros "0000"
from-KERFEW=LOS ANGELES

Motorola... | Answered on Mar 15, 2009


turn bluetooth on your phone on. then on your bluetooth headset hold the power button for about 10 seconds or until you see the bluelight on steady. next on your phone in the bluetooth section klick ok on the search for device option, when you found the bluetooth with your phone it will ask if you want to use that device, klick yes, and it might ask you for a code, enter four zeros "0000" and that should connect automatic.

Motorola... | Answered on Mar 14, 2009


the button might be sticking from use, with a small flathead screw driver carefully pry off the silver part above the button area close to the charging port, you will see 2 tiny screws, next carefully with a tiny flat head screw driver, remove the cap over the bluelight area (the one with the symbol "M") and there is another tiny screw there. open it carefully and once open inspect closely the area that holds the button assembly and see if the contact point is either ripped or dirty or if the rubber is just not flexing anymore....

Motorola... | Answered on Mar 14, 2009


TURN THE POWER OF ON THE BLUETOOTH FIRST...THEN WHEN POWERING BACK ON, HOLD IT FOR APPROX 10 SECONDS AND THEN YOU WILL SEE THE STEADY ON LIGHT....from-KERFEW+LOS ANGELES

Motorola... | Answered on Mar 14, 2009


go to were you find the name of the headset in your phone and click options, is there a connect option? if so you must click ok on it and this will connect......... from-KERFEW-LOS ANGELES

Motorola... | Answered on Mar 14, 2009


the code is whatever you want it to be. the easiest and most common is four zeros "0000" . and you will be connected with your bluetooth. --- from KERFEW=LOS ANGELES

Motorola... | Answered on Mar 14, 2009


ACTIVATING THE BLUETOOTH
You must activate the Bluetooth feature of your phone to be able to establish a Bluetooth connection
between your phone and your SuperTooth kit as well as with other Bluetooth devices.
1.
Press Menu > Settings > Bluetooth > Activation > On.
2.
Press Back as many times as needed to return to standby mode.
PAIRING TO THE CELLULAR PHONE (Not possible while charging the SuperTooth)
Pairing will create a link or connection between the two Bluetooth devices - the SuperTooth kit and your phone.
1. Bring the cellular phone at about 20 cm from the SuperTooth.
2. Turn off the SuperTooth and wait for about 4 seconds.
3. While pressing the Answer Button, turn ON the SuperTooth by sliding the Power Switch to the right. Keep the Answer Button pressed for approximately 10 seconds until you hear a distinctive tone and the Bluetooth indicator LED changes from blinking blue to alternately blinking of red and blue. The SuperTooth is now in pairing mode.
4. While the SuperTooth is at pairing mode, access the Bluetooth menu of your phone. Press Menu > Settings > Bluetooth > My devices > Search new device. The phone will then search for pairable devices until it displays them in the list.
5. Highlight SuperTooth then press Select.
6. Enter PIN “0000” then press Ok. (Wait until “Paired with …“ and “Connected” will be shown briefly.)
7. Press Back as many times as needed to return to standby mode. Pairing is successful if the alternating red/blue lights of Bluetooth Indicator stops and then change to plain blinking blue. Normally, the phone would also show briefly on its display if it’s already paired and connected to SuperTooth or if pairing with it failed.
The SuperTooth kit is now ready to use.

Motorola... | Answered on Mar 13, 2009


you need to depress the button on the headset until the blue light stays continiously on.. then search fro devices from your phone..once the device is found the blue light will flash and blink

Motorola... | Answered on Mar 08, 2009


did not need to unpair. Just needed to have phone search and use 0000 code.

Motorola... | Answered on Feb 28, 2009


Is it in mute mode?
http://www.motorola.com/mdirect/demos/how2_h500/h500.html

Motorola... | Answered on Feb 28, 2009


Did you try pressing the two volume controls at the same time on each side? perhaps it's in mute mode.

Motorola... | Answered on Feb 28, 2009


try the code 0000 this should be its factory setting

Motorola... | Answered on Feb 27, 2009


what you need to do is press the main button down for three secs. (three times) this will troublshoot your headset

Motorola... | Answered on Feb 27, 2009


what do i type when it tells me to enter "passkey'?

Motorola... | Answered on Feb 26, 2009

Not finding what you are looking for?
Motorola Mobility H500 Wireless Headset Logo

354 questions posted

Ask a Question

Usually answered in minutes!

Top Motorola Mobility Radio Communications Experts

Lawrence Oravetz

Level 3 Expert

10543 Answers

Brad Brown

Level 3 Expert

18157 Answers

Dennis

Level 3 Expert

962 Answers

Are you a Motorola Mobility Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Motorola Mobility Radio Communications

  • Motorola Mobility Radio Communications

Most Popular Question

motorolla h500 no steady blue light

  • Radio Communications
Loading...