20 Most Recent Sharp AR-5316 Advanced Digital Imager Copier - Page 10 Questions & Answers


No need ,its automatic?

Sharp AR-5316... | Answered on Nov 12, 2013


For which win platform?

Sharp AR-5316... | Answered on Nov 12, 2013


What display light on?

Sharp AR-5316... | Answered on Nov 12, 2013


It is the left top right button with an 90 degree arrow.

Sharp AR-5316... | Answered on Nov 12, 2013


would have though not. un less it was just rammed in. but then the clips would have broken off at the same time

Sharp AR-5316... | Answered on Nov 07, 2013


try to reinstall the printer driver

Sharp AR-5316... | Answered on Nov 06, 2013


CCD calibration error. Make sure the optics are clean in the machine in the scanner and free of dust.

Sharp AR-5316... | Answered on Oct 19, 2013


The problem is in the fusing unit try these steps:

STEP1: Press continuously CLEAR then INTERRUPT then ZERO then INTERRUPT

STEP2: The panel display will turn off it means that you are inside the simulation if not repeat again step1.

STEP3.Then type 14 then press the print button

If these steps doesn't work you must call an authorized serviceman to check your machine, maybe something is busted on the fusing unit like thermostat or fusing lamp.

Sharp AR-5316... | Answered on Oct 12, 2013


EEPROM error Take to Sharp Service Technician

Sharp AR-5316... | Answered on Oct 09, 2013


BIG QUESTION WHAT DO YOU WANT TO RESET ON THE MACHINE?

Sharp AR-5316... | Answered on Oct 09, 2013


An F2-04 is the IC chip on the toner cartridge was blown by the machine because it was unable to replenish tone in the developer unit , replacing the toner would clear the error but if it is a symptom , and usually is , i would suggest to take it to a Sharp technician to have a look at it, because if the problem is deeper it would just blow the new toner`s IC and that would be a waste

Sharp AR-5316... | Answered on Oct 09, 2013


The printer repair guy just left. I'm paraphrasing what he told me:

The Sharp MX4501N was displaying the error: H3-04. This does mean that the printer was reading an above average temperature for the fuser, for some reason.

He said that in his experience, 90% of the time, this is due to power surges/spikes and not an actual incident of the fuser over heating. A good surge protector isn't normally enough and he recommended that we look around for a cheap UPS to condition the power.

Other things that can cause a higher than average reading of the fuser can be caused by paper jams, where a piece or pieces of the paper are lodges inside, insulating the fuser and restricting air flow to the internal compnents. Printing 15-25 blank sheets through the copier can usually dislodge these. If not, call for assistance.

In order to clear the error code (H3-04) from possible powewr surges/pikes, I was given the following code: #P, *, C, 1,4 PRINT
This will remove most of the codes restricting printing to the copier, however, should the code reappear, contact customer service and arrange for a visit from the local repair person.

I hope this helps anyone else who may run in to the same problemThe error: H3-04. This does mean that the printer was reading an above average temperature for the fuser, for some reason.

90% of the time, this is due to Power surges/spikes and not an actual incident of the fuser over heating. A good surge protector isn't normally enough and recommended that we look around for a cheap UPS to condition the power.

Other things that can cause a higher than average reading of the fuser can be caused by paper jams, where a piece or pieces of the paper are lodges inside, insulating the fuser and restricting air flow to the internal compnents. Printing 15-25 blank sheets through the copier can usually dislodge these. If not, call for assistance.

In order to clear the error code (H3-04) from possible power surges/pikes, I was given the following code: #P, *, C, 1,4 PRINT
This will remove most of the codes restricting printing to the copier, however, should the code reappear, contact customer service and arrange for a visit from the local repair person.

I hope this helps anyone else who may run in to the same problem

Sharp AR-5316... | Answered on Oct 07, 2013


H4 is normally caused by the fuser taking a little longer than normal to warm up. Most of the time it is not caused by the hear rod itself. I will send you the process here is a few minutes.

Sharp AR-5316... | Answered on Oct 04, 2013

Not finding what you are looking for?
Sharp AR-5316 Advanced Digital Imager Copier Logo

1,371 questions posted

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sharp Office Equipment & Supplies

  • Sharp Office Equipment & Supplies

Most Popular Question

sharp ar 5516 maintenance reset

  • Office Equipment & Supplies
Loading...