20 Most Recent
Kenmore Elite HE4 Electric Dryer - Page 7 Questions & Answers
Burning smell
you can unplug the unit , and reomve the lower aces panel (3 screws along the front bottom of unit) youll probalby see an excess of lint built up in which case you can vacuum it out, and then check/clean and or replace your dryer vent
Kenmore elite HE4 quiet pak 9
Front Panel lights not working? Dryer inside light does work? I fixed this twice already on my dryer. Please read this whole explanation
I live in New Orleans where the humidity is very high. I have a laundry room where my Washer and Dryer reside. Kenmore HE4T. I noticed that when I shut the laundry room door, my central A/C pulls hot air from outside the house via the dryer exhaust duct. This causes moisture to build on the inside of the dryer and especially the front control panel. Did you ever see moisture on your dryer?s door even when there were no clothes in it? The moisture collects on the Silicon board that controls the dyers function and basically causes a short.
This is what I do to fix it. You will need a ΒΌ nut driver or socket.
1. Confirm that you have power to the dryer <- is the inside dryer light on when you open the door. YES- keep reading.. NO ? find the circuit breaker and reset it.
2. UNPUG THE DRYER! ! ! ! ! ! ! !
3. Find the 3 screws in the back of the dryer that hold the dryer lid on. Unscrew them and slid the lid back and lift off. Is there moisture on the inside of the lid?
4. Find the 2 screws that hold down the front control panel. They should be silver and will be on top. Do not remove the inside gold screws.
5. Find the 3 screws that hold down the power control panel on the top left side of the dryer. Probably has a high voltage warning sticker on it.
6. Lift the power control panel (sheet metal) part and move it to the right so it lays on the dyers drum. There are some wires attached to it and unless you are a very handy person, I wouldn?t remove them.
7. Lift the front control panel straight up until it comes out of the dryer. There should be some wires that attach this piece to the power control panel. If you are handy, you can remove these 2 clip-on wires from the power control panel by squeezing the black connector locking clip and releasing it from the panel.
8. If you flip the control panel around you may notice moisture on the green silicon chips. Get a hairdryer and take your time to dry them.
9. Dry all components of the dryer with a hairdryer.
10. Put everything back together except for the lid and all the screws. Remember that the front control panel slides down first and then the power control panel sits on top second. Plug the dryer in and see if you get lights, but don?t start the dryer. Unplug the dryer and replace all the screws and the lid.
The problem is that once the dryer gets wet from the moisture, it never dries enough for it to start working again. This is a bad design from Sears/Whirlpool. I learn my lesson that just because its more expensive doesn?t make it more better.
I now keep my dryer and washer door open all the time even when there are no clothes in it. This lets the moisture escape into the house rather than collect in the dryer.
I hope this helps at least one person.
Thanks
Jason Kennedy from New Orleans
Dryer
Squealing could be a loose belt very seldom see this squeaking more than likely the drum rollers
Dryer runs but doesn't heat.
The high and Low thermostatic limit switches must be in working order for the heating element to get power to operate. High limit opens in the event of a overheat condition to cut off the heating element. The low limit cuts on and off to control normal operation of the heating element for a more or less constant heat for drying.
Kenmore Elite quiet pak 9 dryer not heating. I replaced the heating element still no heat
If you are able to replace a heating element, then you are probably able to use an electrical tester, these are cheap (10 or less) meters that will tell you if you have current at any particular point. Start with the wall outlet and assure yourself you have 220, check any other connections to see if what should be hot is hot. Don't forget there is 110 to 220 volts coursing through the machine. Don't get between the power lines and "ground".
Dryer door does not open
I think Kenmore is essentially a Whirlpool. Make sure the controls are not "locked". Read the control panel thoroughly to be sure.
Not finding what you are looking for?