20 Most Recent GE Energy Star WCVH6260F Front Load Washer - Page 6 Questions & Answers

On this section, there are no charges, but there is also a side of this site that charges for advice and even has chat and telephone support.

Difference is normally the completeness of the answer, and the speed that it is answered.

Hi

Please make sure the door seal fine. If not then you'll need to replace it. Also check that nothing is blocking the drain pump assembly. If still the issue is not resolved then the control board has gone bad and should be replaced. Hope this helps...please post back for further assistance.

Daniel

Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101

If the model number you have this question listed under is correct, the part number for a replacement belt is WH08X10024. You can find it listed at appliancepartspros.com for about $37.

If you have never replaced a belt on this type of washer before, the following link explains how:

http://www.fixya.com/support/r3059652-drive_belt_installation_whirlpool_duet

The link is for Kenmore Elite and Whirlpool Duet, but the GE model listed is identical in design.

If you have any questions, please let me know. I hope this helps you.

I am very sure that even if the latch on the door is proper it is not being sensed by the washer. So only you are experiencing the problem of beep when u start and nothing else.You might need to replace the latch assembly behind the front panel.

I believe your problem is a clogged drain hose.  If the pump can't pump anything out of the tub during the spin cycle, the machine doesn't complete the cycle.  Using a phillips head screwdriver, unscrew the three screws across the bottom of the machine, just above floor level.  Remove the panel and look for the 2" drain plug on the right - it's white plastic.  Now, if you have a shop vac, get it out and get ready to **** up all the water that drains out of the tube when you remove the plug.  Alternatively, you can use a bunch of towels.  More than a gallon will come out.  Clean any of the **** out of the screen attached to the drain plug and look for any debris in the tube in which the plug screws into.  This should fixya.

if you have lights on the unit but thats all,remove the top and in the right rear top corner theres a round hockey puck style component with a wire harness and rubber hose connected to it,this is the water pressure sensor,they do go bad

What is the problem with it? Does it run ? Any error codes displayed?

Hi,
When my washer did that, I found that the shocks that hold the tub were bad...

Check out this tip I wrote about the noise and vibration that front loadwashers can make..

Washer Problems Washer noise when spinning
heatman101

1/I suspect2 possible options ,the heat sink in door switch is failing to give 100 % contact any more giving a reduced power supply to circuitry - replace 2/ or power/start button fails to connect .remedy - replace switch , make sure power is turned off first or get service provider to replace it .

Service Test Mode can be entered to view the most recent error codes and/or verify the machine functions.


Press Start/Pause to perform the test when a test mode is displayed, e.g. t01, t02. The test mode t02 displays the most recent error code, E00 if none. Repeat pressing Start/Pause to display up to previous 10 error codes. Press and hold Start/Pause to clear all error codes then displays E00.









Post the most recent error code for further advice and you may complete the test modes to verify the machine functions. Please accept the solution should you find it helpful or informative. Accepting the solution will not stop you from communicating with the expert. You can still communicate with the expert should you need further advice regarding the issue stated herein.

sounds like drain is plugged. this is a fairly easy fix,and you actually get paid to do it. unscrew the bottom panel of your washer should be 3 screws on the very bottom then you will see a white plug that is about 2 1/2" unscrew it (make sure you have a bowl under it water will leak ) and pull it out. this is where you get paid you will find all kinds of change and junk just clean it out reinstall and your clothes will be a lot drier after the spin cycle

Viv, hopefully it's just your filter thats clogged with lint and stuff. You will have to remove the front lower panel and the pump filter cover will be right in front. It just unscrews and pulls out. These models have a pressure switch that will not allow the machine to advance into high spin if it detects water in the tub. This is an easy job, just grab some towels and be ready for some water when the filter cover comes off. Clean out the stuff and see it fixes the problem..Catriver..post back.

You can use a level that you can get at an hardware store. Level it side to side first then front to rear. Here is a video to walk you thru the process.

This is the sign of a pump failure, the brushes in the pump motor are getting weak and this makes it hard to start the pump. Once you spin it it will take off because it had the impeller loosend before starting. I would say at the least you have bad brushes and maybe a bearing in the pump trying to seize on you. I would get a pump motor and keep it handy!

Hi from retired Englishman in SW France,

Quick silly question(s) ;-0)
Are you selecting the right program? Wool is spun fairly slowly and the speed would not be fast enough for normal garments. If you have selected the right program(s) for the particular garments, I would immediately contact the vendor/supplier as the machine is under guarantee, I presume.
Did they install and test it?

Good luck,
John C

And the answer is:
maybe yall could consult this repair manual for a dianoses of your problem? If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Hi from retired Englishman in SW France,

This is symptomatic of either a failing water control valve- it's not closing when it should- or the control board.
Sorry- service call ;-0(
Good luck,
John C