20 Most Recent
Rainbird Rain Bird Ag5 Popup Impact Rotor Sprinkler 12 In Npt - Page 9 Questions & Answers
Powermate 43cc tiller won't start
How did you test spark? Neon spark testers can be misleading. Use a gap type test with spark plug installed.If engine is flooded it will not fire, even with starter fluid. If plug is wet (excessive) then it may be flooded. Dump all the fuel, remove spark plug and pull recoil starter several times to get cylinder and crankcase dried out. Do not refuel.Put a shot of starter fluid directly into spark plug hole. Reinstall plug and pull start rope a few times. If it fires off and dies then it's a fuel flooding (carburetor) issue.If plug is dry when using starter fluid and there is spark and compression, then likely timing is off. You'll need to remove flywheel and and verify keyed portion has not sheared.
7/9/2023 12:20:10 AM •
Garden
•
Answered
on Jul 09, 2023
Renewing the cutting deck on a lr 135
To renew the cutting deck on an LR 135 (assuming it refers to a specific model), you can follow these general steps:
- Safety first: Ensure the lawnmower is turned off, and disconnect the spark plug wire to prevent accidental starting.
- Remove the old cutting deck: Depending on the specific design of your lawnmower, you may need to remove any side panels, belts, or other components that connect the cutting deck to the mower. Follow the instructions provided in the lawnmower's manual or consult the manufacturer for guidance on removing the cutting deck.
- Prepare the new cutting deck: Ensure you have the correct replacement cutting deck for your LR 135 model. Compare it to the old deck to ensure they are the same size and have the necessary mounting points.
- Install the new cutting deck: Align the new cutting deck with the mounting points on the lawnmower. Carefully reattach any belts, side panels, or other components that were removed in the previous step. Make sure the deck is securely attached and properly aligned.
- Reconnect the spark plug wire: Once the new cutting deck is installed, reconnect the spark plug wire to the spark plug.
- Test and adjust: Before using the lawnmower, it's important to test the new cutting deck and make any necessary adjustments. Start the lawnmower and listen for any unusual noises or vibrations. Ensure the cutting height is set correctly and that the blades are properly aligned.
7/3/2023 10:22:42 AM •
Garden
•
Answered
on Jul 03, 2023
38" Bolen riding mower, won't go forward or reverse nor can you push it. Model 13ac762f. What could be the issue?
If your Bolens riding mower is not moving forward or in reverse and cannot be pushed, there could be a few possible issues to consider:
- Drive Belt: Check the drive belt that connects the engine to the transmission. Over time, the belt can wear out, become loose, or even break. Inspect the belt for any signs of damage or if it has slipped off the pulleys. Replace the belt if necessary.
- Transmission Issues: The problem could lie within the transmission itself. It's possible that there is a mechanical issue or a problem with the transmission fluid. Check the transmission fluid level and condition. If it's low or dirty, it may need to be topped up or replaced.
- Brake or Clutch Problems: The mower may have a brake or clutch system that engages and disengages the transmission. If the brake or clutch is not fully disengaging, it can prevent the mower from moving. Inspect these components to ensure they are functioning properly and not stuck in the engaged position.
- Traction Drive or Transaxle: The traction drive or transaxle system on the mower could be faulty or damaged. This system is responsible for transferring power from the engine to the wheels. If there is a problem with the traction drive or transaxle, it may need to be repaired or replaced.
- Wheel or Axle Issues: Examine the wheels and axles to see if there are any obstructions, debris, or damage that may be preventing them from turning freely. Ensure that the wheels are properly secured to the axles and that there are no loose or broken components.
6/28/2023 4:34:30 AM •
Garden
•
Answered
on Jun 28, 2023
1990 Mastercraft Riding mower manual?
If you want it for the tractor as a whole, I would need the model & serial of the tractor. Look under the seat, or on the frame below the seat or on the platform where the seat mounts. It is usually one of those metalic adhesive stickers with the numbers printed on it. They seem to get knocked off or pulled off quite often but without those numbers, I have no way of looking it up for you.
If yu just need engine information, I can find that with the model and type numbers
6/24/2023 6:30:53 PM •
Garden
•
Answered
on Jun 24, 2023
How does the governor spring hook up for the throttle assembly on rally 5 horse motor
To properly connect the governor spring on the throttle assembly of a Rally 5 horsepower motor, follow these general guidelines. Begin by locating the governor arm, a metal lever connected to the throttle assembly near the carburetor or intake manifold. Next, identify the governor spring, a coiled spring with a hook or loop on one end. Attach this end to the designated hook or anchor point on the governor arm. Then, find the appropriate anchor point on the engine block or throttle assembly and connect the other end of the spring, ensuring a secure attachment that provides tension when adjusting the throttle. If needed, adjust the tension by repositioning the attachment points. Remember that specific instructions may vary based on the Rally motor model, so consult the motor's manual or contact the manufacturer for accurate guidance tailored to your engine.
6/18/2023 12:09:28 PM •
Garden
•
Answered
on Jun 18, 2023
Not finding what you are looking for?