Kenwood 2005 KDC-MP5028 CD/MP3 ReceiverFree Standard Shipping - Answered Questions & Fixed issues

yea the got a short somewhere. Horn fuse might or might not work something with the radio. I would say start with the horn. The horn is a controlled short sometimes shorts it self out. Open your steering wheel and work from there. For your radio look at all the fuses that you know work the radio and go from there. What kinda car is it year things like that would help because if it older wires, fuses, fusible links things like that go bad over the years. Especially if you run a lot of power through the wires that was made for that kinda power like upgraded speakers, headunit (radio) amps things like that. Older cars and trucks are make with cheap radio wires. hope this helps

need unlock code bought used car battery died stero needs code dealer has no idea

Here you go buddy:
http://www.fixya.com/support/r538828-security_unlock_code_kenwood_most_models

you will need a remote for this
Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

Last night i got the answer from KENWOOD Support

Press and hold in the SRC button until the unit turns off. While power is OFF,
press and hold FNC and AUTO/TI buttons, and momentarily press the SRC button to
power the unit back on. Continue to hold the other buttons until the unit comes
back on completely.

I did it and it works

Enjoy

MichaelBlackDo you know where I can find the remote key combination to do the same with KDC-MP538U? (To transform it to the European system)

Thanks in advance!

Hey there joe,


Click here, it will bring to a Tip page authored by one of our best technicians (Robotek). He outlines the procedure for clearing the code on most Kenwood models.

If this gets you going, don't forget to give Robotek a rating Remember: Good things come to those who Rate!!

Mike

on your radio there should be 2 sets of outputs high and low you probably have set to low just switch to high and run your speaker wires accordingly to amp

http://www.sirius.com/pdf/manuals/KCA-SR50.pdf

find it here in this manual

yes its called a multi cd changer

hi cant find reoval for this odel, but am 90% sure that : http://manuals.kenwood.novenaweb.info/languages/EN/support/manuals/KDC-MP6090R.pdf

is the same to remove see page 42

Regards


Mark
Blue ICE

hi it sounds like the cd mech is wurring so power should be ok.
try RESETTING the unit with the reset button, you will need a pen tor a pin to do this in most cases. if still no joy, then double check that you are getthing two pwer feeds to the radio
1 should always be there this is the perminant power feed. and the other4 should only be there when the ignition is on.


let me know how you get on.

Mark

Blue ICE
www.blueice-electronics.co.uk

try this

KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!

" protect " is flasing on my w534 cd player and my cd player will not work any more . any ideas

with the unit in standby, press the menu key, use the joystick control to choose aux, and set the aux option to "on"...then press menu again to save...when you next switch on the unit, using the SRC button you can cycle through the available options...cd - tuner - aux..etc etc

Question edited for clarity. Try the ideas in the videos https://www.google.com/search?q=Kenwood+Excelon+DDX9904S+DVD+receiver+reset ..

Me radio kdc2159b is displaying the ward call,how do i remove it

To reset a Kenwood 8070 receiver without a remote, you typically need to locate the reset button on the device itself. This button is often small and recessed, so you may need a paperclip or a similar tool to press it. Consult the user manual or look for the reset button near the power or input/output ports on the receiver. Once located, press and hold the reset button for a few seconds until you see the receiver reset. Keep in mind that this process may vary slightly depending on the specific model of the Kenwood 8070 receiver.

Kenwood KDC-138 Instruction Manual [Page 18]

ManualsLib https://www.manualslib.com > ... > Instruction manual If the "E-99". code does not disappear, consult your. nearest service center. IN (Blink):. The CD player section is not operating. properly. ? Reinsert the CD.

My Kenwood KDC-d301 is giving me a E-4 error message ...

JustAnswer https://www.justanswer.com > car-electronics Aug 9, 2010 - Hello, The issue is most likely that the laser lens in the CD player itself is dirty, and not the disc. It may have been initially caused by a ... 1 answer · Top answer: You need the Kenwood radio keys that came with the unit to slide it out of the dash. It sounds ... Missing: 138 ‎' Show results with: 138

I have a KDC 138. It is stuck on OCER and will not reset.

JustAnswer https://www.justanswer.com > car-electronics > 5lw8u-... Sep 27, 2011 - This actually is DCER - you have a blown speaker. The radio is sensing a ground on the speaker circuit. Check that and let me know. If you leave ... 1 answer · Top answer: Thanks for stopping by: This actually is DCER - you have a blown speaker. The radio is sensing ... Missing: E- ‎' Show results with: E-

Cd Player Unit - Kenwood KDC-138/138CR Service ...

ManualsLib https://www.manualslib.com > ... > Service manual Kenwood KDC-138/138CR Manual Online: components description, Electric Unit, Switch Unit, Cd Player Unit. Controls Fm/Am Tuner, The Changer, Cd Mechanism, ...

This Service Manual is probably close enough for dealing with the power supply https://elektrotanya.com/kenwood_dpx-8020md_sm.pdf/download.html https://www.google.com/search?q=Kenwood+DPX-8070mj+service+manual ..