Top 20 Sony BRAVIA KDL-V32XBR1 32 in. LCD HDTV Questions & Answers

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. https://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary. Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

I have never heard of a warm-up problem on a digital television. Unlike the old CRT TVs and monitors, digital panels don't have to warm up. I would go with the TV repair persons assessment that you've got a bad panel.

If this happens on all disks then the unit is dying a slow *****. Get ready for the DAY it goes completely.

I will try a new T-CON board first.

T'Con Board fault. Check and replace it. If you wish to get more details visit the site linked here. http://electronicshelponline.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent.

Refer its user manual for details. If you do not have the user manual. try the site linked here, and download it for free. www.retrevo.com/ Electro help

Back-light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/

You are better off replacing the whole unit. Even if you can find the parts from sony you need to have a technician replace it for you so you are looking at about the cost of a new TV just to replace the screen. If you are seriously committed to finding one start here Products Parts Accessories or here http://www.searspartsdirect.com/partsdirect/part-model/Sony-Parts/Television-Parts/Model-KDLV32XBR1/0996/0333600?pathTaken=&prst=0&shdMod=KDL-V32XBR1 Good luck

have the same problem with my bravia 32 bx320

Power low of main power supply 10.5V line PLEASE CHECK 10.5 v supply your power supply board is defective

I need more info. Are you using antenna connected to RF input or are you using cable box, sat box or ATT Uverse? If connected to antenna . go in menu or Home on Sony. Press setup and look for channel scan. Set to antenna and do auto scan. If cable or other provider box set tv to ch 3 or what ever provider says. You are then using the tuner in that box. You will use providers remote to change channels. Be sure in setup that tv is set to cable if cable box is used. Hope this helps but the info you posted could be more descriptive.

IKR Error at power on 05. 5 blinks denotes this. Actually, the fault is related to its main digital board, and the work will not an easy one. Anyway, http://electronicshelponline.blogspot.com/ check this link. Pull up previous posts there, either by its left side bar, or view it in Timslide option, and see whether there is something to help you. If you're not sound in electronics, no need to proceed. Contact any service technician or authorized service centre for Sony.

I have a Sony model KDL-32BXR6 that the TV Guide first showed no listings this past weekend. Last night when I entered the Guide the screen displaying the Setup/Display Setup Progress came up stating "In Progress". Same thing this morning. Something must have changes with the input signal if this occurred with two different sets.

does the screen go black when the screen goes out?

Either USE a HDMI cable or VGA Cable !

Here are a few more troubleshooting steps you can try when your TV picture is just snow. I see that you have already rebooted your TV, but did you turn your set-top box off and on, too?1. Does the picture show when you play a DVD? 2. Check all of the connections between the TV, outlet and set-top box and make sure everything is secured.3. Is your TV set to the correct channel (typically 3, but in some areas 2 or 4)? 4. Press any key on the remote to see if the correct mode lights up. (Ex: if you have cable, the cable button should light up). If it doesn't, press the correct mode's button to regain control and change channels.5. Call your service provider and make sure it's not an overall service outage. 6. Do you have sound but no picture? If so, it could mean a backlight failure.For more suggestions, see TV black screen or snowy screen for troubleshooting and solutions. I hope this helps!

Check the speakers first. If they are OK, replace the audio output card.

This is an indication of protection error and might require attention of a qualified service technician.