Press the [i+] or MENU button on the remote control to display the DIGITAL INFO menu.
Press the BLUE button to display the MAIN MENU.
Press the UP or DOWN buttons to highlight AUTO TUNING then press the OK button to display the AUTO TUNING MENU.
Press the RED button to start the auto tuning process for all available digital channels.
Wait for the process to complete.
If you wish to CANCEL the auto tuning process whilst it is processing then press the BLUE button at any time. You may lose some channels when you retune the TV as the channels have been rearranged. To locate them look at the EPG although you may still find that some channels are no longer available on FREEVIEW. See the following link for additional information http://www.freeview.co.uk/_retuneinfo/ If the above process does not work then check the link above for additional information and also visit the accompanying site links below to find more information for your model of TV / FREEVIEW box. For troubleshooting the retune procedure visit http://tvretune.co.uk/troubleshooting/ For specific model information visit http://tvretune.co.uk/productmanuals/
There is a bad capacitor on the power board of the television that is why you are having the blurry double vision on the television. Have the power board checked for bad capacitors that need to be replaced.
Hope this helped.
All the best
Hi, The Standby/Power light of the TV blinks when there is any internal malfunction in the TV. The self-diagnostic function of the TV will cause the STANDBY light to blink or flash when the television detects an issue. The number of times the STANDBY light flashes corresponds to a specific issue. Few examples are given below; some of the issues may be resolved without the need for service. 1 blink / 2 blinks / 5 blinks: - This indicates that there may be a power-related problem with your set. 3 blinks: - This indicates that there may be a power-related problem with your set. The set will need to be serviced to allow a technician to determine the specific issue that needs to be repaired. If the power light flashes three times in sequence in a Lamp TV, the lamp cover is not securely attached. Reattach the lamp cover to resolve this issue. 4 blinks: - This indicates that there may be a back light or lamp power problem. 6 blinks: - This indicates that there is some kind of audio problem with your set. 7 blinks: - This indicates that there is a temperature problem with your set. Please check to make sure that the air vents on the sides and back of the set are not blocked or clogged and there is adequate ventilation around the television. We recommend that you check and clean the vents periodically to make sure the set receives adequate air flow. If the problem continues, the set will need to be serviced. 8 blinks: - This indicates that there may be a video-related problem with your set. If the flash sequence is not listed above or the light continues to flash, follow the steps below to perform a power reset: Try the following steps to check if the issue can be resolved. Turn off the television. Unplug the television power cord from the electrical outlet. Let the television remain without power for 60 seconds. Plug the power cord back into the electrical outlet. If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television. If the issue continues to occur, service may be required. Thanks for using Fixya.
This issue is related to a power problem. I don't think it's a lamp problem.
The problem is consistent with overheating on the power supply board of the TV.
power supply board of the TV has few capacitors and IC. If any of these
IC's gets short or become weak, it can cause the TV not to turn on.
current passes from electric outlet to the power supply board of TV.
The current also goes to the weak/faulty part, then the current stops
or slow and the board overheats and TV shuts off on it's own.
This is a
common problem faced by many other users too. To
solve this issue, check the power supply board and read it with a meter and
continuity tester, in order to detect the faulty part and replace the faulty part on the board which is
short due to which power supply board.
Sony specifically uses GM1 Board. In other words, Sony power supply board is called "GM1 board"
It's a bit
technical job but yes its not at all a costly repair to do or get it
done by the technician.
can buy these part at any Fry's or Radioshack store or you can
order them online at vendors like "mcmelectronics.com"(look for
electrolytic capacitors). After replacing these capacitor (capacitors)
most likely the normal operation will be restored. Or you can by a
refurbished complete power board to save you some stress.
this task is too technical for you, you can call a family or friend who
has the ability to assist you (two heads are better than one).
Six blinks means a problem with the High Voltage circuit and the TV shuts down to safe diagnostic mode. Usually the thermal fuse is open. It's attached to the light housing and needs to be replaced with the new style 1-910-023-93
You have a Bad Optical unit Block /also known as the light engine.
part number A-1132-204-A
Encompass Parts has 3 of them $1,499.99- $550.00 core refund = $949.99
PTS rebuilts light Engines 1-800-844-7871
Press the power button key to make it in standby mode and then follow below.
> Press the button key on the remote control in sequence.
> "Display" "Channel 5" "Volume ( - )" "Power".
Let me know what will displays on the screen.
Hi. Yeah, lightning can wipe out electronics really easy. I would file a claim with your homeowner's insurance policy. Surely they have these kinds of things in your policy. As far as getting it fixed, first you will need to get estimates from 3 different companies for your insurance company. I would take it to BestBuy, Fry's, Staple's, or CompUSA. All these places have service centers, and I am sure that they have all seen lightning strike damage and insurance quotes.
I hope that you get it going again, or that you get an approved claim, as it was an act of God, not an intentional act which affected your tv.
All Plasma and LCD TV have boards that control vertical and horizontal output to their respective areas. They are connected to the screen by ribbon cables. If one of these boards fails all together, has a failed chip, a bad connection, or a bad ground somewhere it will result in a black line in the area of that board. A bad ribbon cable connection on the bottom will result in a vertical black bar though the screen. Many times resetting the connection will fix it, if the ribbon cable has been nicked there could be a severed connection. They an sometimes be fixed, but it is a pain. An yes I have done it, but the bar is gone. The same will happen if the chip that outputs to that area opens. The connectors are the first place to look paying close attention to the cable, they are extremely delicate so great care must be taken . Good luck in handling the fault.....
This is a common problem an a failry easy DIY fix.
Plasma and LCD TV sets are prone to having capacitors in the power supply section fail. This is the most likely cause for the probem you describe. When capacitors fail your will commonly see one or more of the following symptoms.
Hi, 4 times red standby light indicates problem with exhaust fan that is not running for some reason. Recheck fan that you replaced and make sure its connector is plugged properly and it running freely. 4 times red light blinking is fan error in this tv. Thanks.
hello..I think your problem is on power supply of your unit...that have loose board connection on the parts you can fix it by re-solder all parts of power supply..use soldering iron and lead after install it again and try to power on again try this process and if its help you please rate me thank you