HP PL5060N 50 in. Plasma HDTV - Page 3 - Answered Questions & Fixed issues
A panel in the middle
A panel in the middle of the screen is usually closed captioning TEXT 1 or TEXT 2. Please press the closed captioning button on your remote control until it is off or find the closed captioning setting in your television's menu and set it to off.
If you are connected to a cable tv box or a satellite receiver you may also have to disable captioning on it.
I have a hp pl5060n 50
SORRY IT LOOKS TO ME UR SCREEN IS SON THE WAY OUT
CALL HP SERVICE CENTER AND TELL THEM UR PROBLEM
My HP 50 inch Plasma
Hi
Thanks for using FixYa. From what you have described it seems to be the issue with Y-main however, the logic board should also be checked. These boards are located on the right side of the unit and to check them you’ll have to open the back of the unit. Once you have opened the back also check for any blown/bulged capacitors. All this is only recommended if you have electrical expertise & know how to solder/re-solder components as these units contain high voltages even when in off position. The cost to get this repair will be around $300 and a bit more if the board is replaced. Please do accept the solution if the issue is resolved or post a comment for further assistance.
Thanks
Rylee
Plasma tv has red fuzz
A picture is worth million words in this case.
Generally, red bleeding in plasma TVs is usually caused by bad (or differently adjusted) Y-sustain board as well as bad power supply.
6/14/2010 4:29:36 AM •
HP PL5060N 50...
•
Answered
on Jun 14, 2010
•
1,407 views
I am looking for a power supply module for the hp
try to find a part number on the board. you can punch this # into google to find a part. hp used different brands so you will have to get the number off the board. look for buldged caps, maybe you can fix the board if it has some. google "bulged cap" to see what they'll look like
Lines on a plasma tv
Vertical lines on the screen is almost always a drive board. This is part of the plasma panel. I don't think you will want it repaired.
Thick Vertical Line
the power supply is defected a capacitor filter is leaking.have a tech repair your tv.good luck.
HP PL5060N 50 my plasma will not start, I have a
The "Clicking sound is what gives it away. It would seem that your unit has some sort of PSU
fault, or a problem that is shutting down the Power Supply Unit, PSU. This
happens so that no further damage, and possible fire will occur.
You need
to take the unit to a reputable service centre/man and ask for a firm
"Quote" for the work to be done.
12/18/2010 11:04:45 PM •
HP PL5060N 50...
•
Answered
on Dec 18, 2010
•
1,007 views
My HP 42 incher died after 2.5 years.
HP doesn't make the price for the main board for your TV available on their website, so you'd have to contact them to get an idea of the cost. Likely it will cost at least $300 but could cost a lot more. If you've had the set for 2.5 years, you'll want to ask yourself if you want to put $300 to $600 or more into the repair of an out of warranty TV when you can purchase a new 42" Viore LCD that's 1080p from walmart.com for $578. Their 32" of the same brand is $349. They have other more popular and more expensive brands as well, but the point is what you'll spend to repair your TV would buy one that is brand new with a fresh warranty. And keep in mind that Wal-Mart's extended 2 yr service plan costs less than $100.
I hope I've provided you useful assistance and that this information
allows you to make an informed decision as to how to proceed from
here. Please be sure to vote on my response. I hope I've earned a
good rating from you today.
Please post a comment if you need
additional assistance so that I can help you further.
50 inch HP Plasma Gone Wild...
Here's the number to HP case management 877-917-4380 ext.79, try this number and be firm that they need to fix this, I just had an HP plasma that was 3 yrs old replaced for free, no charge. Good luck
Our HP 50" Plasma TV needs a new Input mainboard
It is hard to find a company that will tell you where the parts come from. Most parts you cannot purchase in america.
Here is a website I would suggest that will help you at best!
Please copy and paste in your browser
http://h20141.www2.hp.com/hpparts/partsdirectory/catalog_solutions_AP.htm
Where is the Logik LPV 09 HP reset button
The location of the reset button on the Logik LPV 09 HP would likely be in the owner's manual or on the company's website. It is also possible that the device does not have a physical reset button and can be reset through software or by unplugging the device for a certain amount of time. If you cannot find the information in the manual or on the website, you should contact the manufacturer for assistance. if i was able to help my cashapp $ralphpapi thank you have a blessing day
I try to start a HP iq775. When I press the power button I heard one short beep and I see a red light red and then blue, and turn off inmediately. The PC won't start. The power supply works fine. Help
All HP iq77x all-in-one PCs suffer from the same problem of a faulty motherboard. This is primarily a soldering issue on the graphics chip,which develops cracks in the solder balls. The PCs contained a separate graphics card, which goes faulty first. This can be removed and the display connector can be moved on the motherboard to use the on-board graphics. This will eventually show the same issue. A short term fix was to heat the graphics chip with a hot air gun or other means (plenty of suggestions can be found on-line) which sometimes works for a few weeks at most. The only 'permanent' fix is to have the chip professionally removed and re-soldered; an expensive option.
If you are lucky, your PC is still wired to use the add-on graphics card, in which case you might be able to remove this and rewire for the motherboard graphics.
Not finding what you are looking for?