Top 20
Samsung HP-T4254 42 in. Plasma Television Questions & Answers
About a week ago when I turned on my 42in Samsung
Check the speaker/s. If found OK; check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Pull up older posts. Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.
http://electronicshelponline.blogspot.com/
Samsung remote HP-T4254 need code please
If you need the code list for the original HP-T4254 remote, BN59-00599A, these are listed in the manual starting at page 22. The steps to program the remote are on the preceding page. Crutchfield has the manual on the product page:
http://www.crutchfield.com/S-TYaga4aDv9F/p_305HPT4254/Samsung-HP-T4254.html . The direct link to the manual is
http://pdf.crutchfieldonline.com/ImageBank/v20071022131600/Manuals/305/305HPT4254.PDF .
Please note that the codes programmed into the remote will probably not operate devices that are newer than the TV. Sometimes electronic devices that were released less than 6 months before the remote was programmed will not respond to the available codes in the given remote.
If you are trying to find a Samsung TV code that will work with another remote, please indicate which universal remote you are trying to program. (There is a Redi-Remote replacement for the BN59-00599A that does not function as a universal remote.)
I hope this helps.
Cindy Wells
Replace the power board my Samsung 4254 plasma tv , won't come on ,no picture and clicking sound
Fault at its main digital board.
Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.....
Sound is off and on
If your looking at channels in the high numbers on cable, make sure that you are not going through a cable surger protector with the cable. They cause a problem on the high cable channels.
Panasonic TH-50PZ85U plasma clicks on has no
Ihad that problem with my Vizio 32" and was told by the repairman that my motherboard was fried & it would cost me 200 bucks to get it fixed . Needless to say for another $69 I bought a new one with an extended warranty. I apologize if I gave you bad news.
How to enter code on xfinity remote
This sites helps you choose which codes to use depending on the remote you have and the TV you're trying to program:http://customer.comcast.com/Pages/HelpNFC.aspx?print=false&id=remotes
Mosfet keeps exploding
Well its clear you have a nasty short somewhere, problem is with no schematics for this set how will you find the problem much less get the correct part?Might be better to shop for a different board to replace this board with.
How to troubleshoot Samsung plasma tv power supply
If relays are clicking, the problem could also be the diode connected to the relay or its own power supply. Check whether the relay is getting power enough to remain activated. This chattering can also be caused due to relays becoming weak or by short circuits on its load.
I have sound but no picture
are you watching a local channel or a movie using a dvd player?. then the screen totally black or with white screen only?just let me know first so i can give further solution.
Smoke and poping
I would check the ballast (the power supply may need to be replaced)
Not finding what you are looking for?