20 Most Recent Sony BRAVIA KDL-46V3000 Television - Page 4 Questions & Answers

Chances are the problem is in your signal board. I have repaired this once in this TV. It was under warranty at the time. The fix was to replace the signal board. I would imagine on a component level, you will rework the board. Testing capacitors and replacing those that are weak or bad will be the fix. Thanks for asking and show all hands of support!

Sorry to hear that!

But you have a dead row of pixels.

You should contact Sony for a warranty replacement as fixing this yourself is all but impossible.

Once again, sorry to hear this and hopefully Sony will provide you with a prompt response!

Hi,

The Standby/Power light of the TV blinks when there is any internal malfunction in the TV. The self-diagnostic function of the TV will cause the STANDBY light to blink or flash when the television detects an issue. The number of times the STANDBY light flashes corresponds to a specific issue.

Few examples are given below; some of the issues may be resolved without the need for service. 1 blink / 2 blinks / 5 blinks: - This indicates that there may be a power-related problem with your set. 3 blinks: - This indicates that there may be a power-related problem with your set. The set will need to be serviced to allow a technician to determine the specific issue that needs to be repaired. If the power light flashes three times in sequence in a Lamp TV, the lamp cover is not securely attached. Reattach the lamp cover to resolve this issue. 4 blinks: - This indicates that there may be a back light or lamp power problem. 6 blinks: - This indicates that there is some kind of audio problem with your set. 7 blinks: - This indicates that there is a temperature problem with your set. Please check to make sure that the air vents on the sides and back of the set are not blocked or clogged and there is adequate ventilation around the television. We recommend that you check and clean the vents periodically to make sure the set receives adequate air flow. If the problem continues, the set will need to be serviced. 8 blinks: - This indicates that there may be a video-related problem with your set. If the flash sequence is not listed above or the light continues to flash, follow the steps below to perform a power reset: Try the following steps to check if the issue can be resolved. Turn off the television. Unplug the television power cord from the electrical outlet. Let the television remain without power for 60 seconds. Plug the power cord back into the electrical outlet.

If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.

If the issue continues to occur, service may be required.

Thanks for using Fixya.

If you have the same problem on any sources (dvd, tv...) then see with your retailer or directly with Sony customer services. There's a problem either with the display card or the panel.

hi,
That problem because tack switch volume short. Open it and replace it.

. The tv is in stand-by mode and the red power led is on. You must push a channel button.

Sony has extended warrenty on 46 XBR4 & 46 XBR5 for picture anomalies - like yours. Check with Sony customer service. Good Luck.

Hello yhill...You can connect your computer up to this tv and use it as a computer monitor.


Using the tv remote push the input button and then scroll down through the choices and at or near the bottom of the list you will see the computer. Joe

Thanks for choosing Fixya!

I really do not believe that to be serious. This is an indication of receiving a strong signal. You may ask a cable TV or satellite provider to adjust the attenuance signal received through the cable/satellite box.Thanks for asking and show a few hands of support!

Most likely the input box that have the problems.Because the input box is another hurtle for the video signal to goes through to get to the tv.Take all the devices out of the input box hook it up directly to the tv should solved this problems.

It is the lcd panel failing, the same as mine. See link
infofrobetterbuys.blogspot.com

could be a few things and I will give you some ,if digital your reception is bad and showing little blocks,check your cable or your dish if you have dish go to setup and check reception bec ause you aren't getting a good signal. you could have a bad cable ,you aren't jacked in properly or at times the coaxial hook up on your set will come unsoldered and be loose.Make sure you have everything ok with another set possibly to see if you have a problem with just that location. definrtly sounds like your set is trying to make a picture out of a garbled sigmal do it isnt yoour set unless you have a problem with your jack in back as stated or you r tuner is bad which I doubt

you should be able to hit the display buttton on the remote to get this to go away

Hi,
Let me know tv is hooked with cable box or some thing that sounds breaks in HD channels?
If tv gets signal from cable box then unplug cable box from wall socket for minute to get it reset, replug back in and turn it On and check.
Thanks.