20 Most Recent Sony BRAVIA KDL-46XBR2 46 in. LCD HDTV - Page 6 Questions & Answers

The tcon bard or the LCD panel is faulty. Can confirm by replacing the TCON board. If you wish to get some details; check the site linked here. Pull up older posts http://electro-medical.blogspot.com/

http://www.sony-asia.com/microsite/bravia_connectivityguide/soundbar/index.html I don't think blue tooth is an option.

Based on the information you have provided for your model and the issue you are currently having with the red light flashing 4 times, we would like for you to try the steps available below:

1. Unplug the television power cord from the electrical outlet.
2. Disconnect all devices from the TV.
3. Let the television remain without power for 2 minutes.
4. Plug the power cord back into the electrical outlet.*
5. Turn your television on.

* If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television. Copied from someone else's post. I agree with the steps this person posted. If this does not work call the manufacturer. You could see how much it would be to fix vs. the cost of buying a new one.

How old is the LED TV Shaaz? It could be going bad

Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.

HI its Balancer error please change Balancer board

HI please push the menu batten from remote & go to sound adjustment menu there is a option available that is speakers sound fix or variable

open the setup & go to factory setup & perform factory sate up during this please select home mode not shop mode after this tv become normal

please go to factory rest feature & turn on every setting become back to original position

Return it, it is a faulty remote if just days old and not functioning.

TV is telling you that something is fubar with that connection.

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://electro-medical.blogspot.com/

Follow these steps to troubleshoot if there is no sound or intermittent sound from the speakers. IMPORTANT: Not all of these features and/or functions are available on all products. Consult the instruction manual that came supplied with your unit to verify if your particular unit has these features, or if more detailed information is required to perform any of the steps below. NOTES: Click on the appropriate link below if the issue is occurring with a particular device or connection.

• If you are connecting a computer to the audio system follow this general information about connecting an A/V component to a computer.
• If the sound issues are occurring when using a Bluetooth wireless device, refer to this additional information.
• If the sound issues are only occurring when using the audio device with a TV, refer to this additional information.
• Because each of these steps represents a possible solution to this issue, check the sound status after completing each step.

1. Make sure the MUTE function has not been activated.
2. Try turning up the volume level.
3. Check that there are no headphones connected.
4. Try setting the Audio/Video (A/V) receiver to a different Surround Sound mode.IMPORTANT: Verify that the source you are playing is encoded with Surround Sound audio. If not, the audio will be very difficult to hear using a Surround Sound setting. Set Surround Sound to OFF when playing a source that is not encoded with a Surround Sound signal.
5. Check each speaker to make sure they are properly connected to the A/V receiver.
6. Perform a Test Tone function to verify if the speakers are working correctly.
7. Verify all external audio sources are securely connected to the appropriate inputs on the A/V receiver. NOTE: If the audio is being sent from a television to the A/V receiver, then it may be necessary to disable the internal speakers of the TV or set the audio output of the TV to FIXED or VARIABLE. If the audio output of the TV is set to VARIABLE, then you will need to increase the volume level of the TV.
8. Make sure the correct audio input is selected on the A/V receiver.
9. Confirm what type of HDMI® devices are connected to the A/V receiver and then check the following:
   1. Test each one of the HDMI inputs on the A/V receiver to confirm that all of the inputs for the A/V receiver are working.
   2. Try a couple of different HDMI cables to verify there is not a bad set of cables.
   3. Unplug the video source from the A/V receiver and connect the source directly to the television. If there is still a problem with the audio, continue to the next step. If connecting the source to the TV corrects the sound issue, service will be needed on the A/V receiver. NOTE: Additional troubleshooting steps are available to troubleshoot instances when the audio, video, or both goes out when using an HDMI connection.
10. Verify the DEMO (demonstration) mode is not active.
11. Change the ATT (attenuate) setting. NOTE: The procedure to change the ATT feature varies by model.
12. Reset the A/V receiver back to factory specifications.

The troubleshooting steps listed above should resolve your issue. If you have completed all of the steps and the issue is not resolved, service may be required.

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced.

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Firmware update procedure to many popular TVs are given. Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Bad symptom indeed. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Line, faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent.