Sony BRAVIA KDL-46XBR2 46 in. LCD HDTV - Answered Questions & Fixed issues
When TV first turned on often has blurry dark lines
If you wish to get some details; visit the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
Line faults & possible causes to LCD & Plasma screen are given with illustrations
. You can get an idea about the fault to an extent. Faults to all LCD & Plasma screen are similar, irrespective of its brand and screen size.
Search the site by type in the "BRAND NAME" of your device; (
Exclude the model number), in the "
Search box at the top right of the display window of the Homepage" to get gathered related posts...
6/27/2017 5:39:31 AM •
Sony BRAVIA ...
•
Answered
on Jun 27, 2017
•
232 views
Volume control not working
Most of the time one of the switches under the control buttons are bad on the control panel of the TV.
7/28/2016 5:38:07 PM •
Sony BRAVIA ...
•
Answered
on Jul 28, 2016
•
1,559 views
Sony KDL-46XBR2 screen is black and no audio. Replaced the Power Supply board (G1) with no help or change
Fault at its main digital board.
Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.
4/18/2016 8:11:44 AM •
Sony BRAVIA ...
•
Answered
on Apr 18, 2016
•
1,041 views
My sony bravia had two thirds of right side was
would say that the screen lights have gone. usually they flicker for a while then come on. then off etc. more than half the screen has gone so the power from the inverter is not being used so it turns off the tv. it is a very fiddly job replacing them as you can damage the screen in the process. more easyer just to get a new screen.
10/3/2013 3:34:56 AM •
Sony BRAVIA ...
•
Answered
on Oct 03, 2013
•
143 views
46xbr kdl hi for some reason my tv as froze on channel 44...it is set in the programs list and i cant remove it...
you could try returning in all of your channels from the main menu the tv can do this automatically but you need to select the procedure1. click on the home button 2. scroll sideways till you reach settings 3. in settings scroll down or up and click on digital set-up (centre button of your scroll control) 4.then scroll down to, and click on digital auto tuning (centre button of your scroll control) this will activate automatic channel tuning the tv will do the rest and will wipe out old settings and retune in all channels
6/5/2013 10:55:57 AM •
Sony BRAVIA ...
•
Answered
on Jun 05, 2013
•
205 views
No Picture and No sound for 20 to 30 minutes.. At
Hi,
this could be a problem with the power supply in the tv, it is common especially on some Samsungs
and specific repair kits are available quite cheaply if you have good
soldering skills, this can also apply to many other Flat Screen TV's .
Usually this is caused by capacitors that have
dried up and split, you can normally tell as the capacitors are bulging
on the pcb, you can get them in a kit as I said eBayer's sometimes do them
or you can buy them indivually from a good electronics components
supplier, make sure you get the correct values for each!! marked on the
side of the capacitors in xx/x V, xxx/x uF and 105oC. (the x's represent numbers)
The picture
below shows the type of theing that happens, the brown ones are
bulging/split on the top whereas the black one is fine.
High Voltages can exist in these sets, never attempt anything while plugged in and
if in doubt do not attempt it yourself and seek the advice of a qualified TV Technician.
There could also be dry solder joints on the panel, usually applies to the power supply as it's mainly these get the hottest.
Here's an example of what dry joints look like.....
High Voltages can exist in these sets, never attempt anything while plugged in and
if in doubt do not attempt it yourself and seek the advice of a qualified TV Technician.
It's also worth considering claiming under the warranty for replacement or repair through you dealer if warranty is valid.
Hope this helps (: don't forget the thumbs up if it did :)
Midge.
2/20/2011 3:25:42 PM •
Sony BRAVIA ...
•
Answered
on Feb 20, 2011
•
282 views
Hi got a few lines come across tv
Hello,
All plasma an LCD ts have boards that control vertical and horizontal output to their respective areas. They are connected to the screen by ribbon cables. If one of these boards fails all together, has a failed chip, a bad connection, or a bad ground somewhere it will result in a black line in the area of that board. A bad ribbon cable connection on the bottom will result in a vertical black bar though the screen. Many times resetting the connection will fix it, if the ribbon cable has been nicked there could be a severed connection. They an sometimes be fixed, but it is a pain. An yes I have done it, but the bar is gone. The same will happen if the chip that outputs to that area opens. The connectors are the first place to look paying close attention to the cable, they are extremely delicate so great care must be taken.
Hope this help in solving the problem......
12/9/2010 1:10:59 PM •
Sony BRAVIA ...
•
Answered
on Dec 09, 2010
•
235 views
Sony BRAVIA KDL-46XBR 46 in. HDTV LCD
I hope this helps
It seems Sony is extending the warranty on your TV
http://esupport.sony.com/US/perl/news-item.pl?news_id=378&template_id=1
IF YOU FOUND MY SOLUTION HELPFUL PLEASE VOTE 4 THUMBS UP.
(any less hurts our averages)
Thank and Good Luck!
2/4/2010 11:51:12 AM •
Sony BRAVIA ...
•
Answered
on Feb 04, 2010
•
1,064 views
Troubleshooting
A 10 times flash is some type of internal communications error in the set. Not much you can do, it needs a qualified tech. One thing you could try is unplugging it for a day or so to see if it will reset itself
10/18/2008 7:07:05 PM •
Sony BRAVIA ...
•
Answered
on Oct 18, 2008
•
175 views
Sony Bravia 46 XBR has the input bar stuck at the top of screen.
Unplug the TV for a while and hopefully, that should reset the circuity. If you're using the original remote control, check for the display button and press it.
I would also suggest doing a factory reset if your TV has that feature and if the TV allows you to do it after unplugging it.
9/30/2022 3:10:56 AM •
Sony BRAVIA...
•
Answered
on Sep 30, 2022
•
60 views
How can I watch Netflix on a tv Sony wega that isn’t hooked to the internet. It’s wirelessly connected to Vizio ( smart tv Netflix built in) but I want to be able to watch in a different room
netflix is a 100% internet web site , streaming site.
thus the net in flix.
what did you mean by hooked?\
do you have internet at home at all?
do other things in home work to the internet, like PC or cell phones.
what I can not under stand is (different room) this phase
implies some rooms do work (netflex)
and wifi gets weak if my move any TV farther from the home router
and will fail past 25 feet or more. wifi is super weak through walls
for sure brick, or 2 walls.
if home is small one wifi access point is all you need
if huge home more.
distance matter, TV to router.
no TV model # told. (tells me wifi spec)
if you said my TV works in room 1 but not room 2, wifi;.
it be super more easy to answer.. is this true?
if true , get a tech to upgrade your wifi.
or go wired, Ethernet.(a better home upgrade)
3/24/2022 2:24:22 PM •
Sony BRAVIA...
•
Answered
on Mar 24, 2022
•
333 views
I need to remove the back off a Sony Bravia KD-48X81J
The front and back pieces are like a clam shell and are compression fit with tabs into one another. You need to use something like a guitar pick or spudger to separate the pieces. Dont use metal objects due to damage that will happen to the plastic .
8/25/2022 5:14:39 AM •
Sony BRAVIA...
•
Answered
on Aug 25, 2022
•
76 views
Not finding what you are looking for?