20 Most Recent
Sony BRAVIA KDL-40S2010 40 in. LCD Television Questions & Answers
Sony bravia kdl-40v5500 tv turns off and on
moved you out of computer repair it is not one.
first off the
remote can be failing !!
first try fresh new batteries
also if kids spill drinks on the remote the buttions can fail
even turn on , not touched.
turn TV on , and move the remote to farthest room. see if TV stays on.
or turn on TV and remove remote battery fast.
ok now, yes/.no//
some TV have no on button or is the only one on the TV,
I really do not want to read your manual
but if there that button on TV> (on/off)
remove the remote batteries
then turn TV on with its only button, on side of TV
cured?
super simple tests, to do no? and super effective facts learned and even cures based on results.
ok read you manual see googled in 5 seconds
and yes center right bezel LCD had
Press
1
on the TV to turn on the TV
any remote abuses or got wet will fail.
easy,
take out the batteries, push 1 above.
Sony Bravia standby light flashing 6 times
there is a bad ground may on the cable check the voltage on the cable & set if on cable call the cable company. if tv call sony they may help with cost may be still under warranty
Trying to connect laptop to
Hi!
First let's be sure that video signal is coming out of your laptop. You did nor mention your laptop make/model and the connection cable type you are using between laptop and TV (VGA or HDMI or S-Video ). I'll assume it is a common VGA cable.
Now, on every laptop the user can choose where the image is displayed: on the laptop only, on the external monitor/TV/projector or on both displays. This can be done by pressing the Fn key toghether with one of the F1 to F12 keys. Usualy it is Fn and F5, but other laptops use other key instead of F5. (please check the icons on your Fx keys, there must be something like two displays side by side). Each time the keys combination is pressed, the image switches between the 3 positions: only laptop, only external, or both displays.
Please let me know if it helped.
If you are using something else than VGA cable, please post again also mentioning what type of laptop you have.
Regards,
Bogdan
Demo mode keeps on popping
hi,
you can exit the DEMO MODE by the following setup.
Power ON the television
1. select "TV" mode (not AV, demo mode can't switch off when ur in AV)
2. Press the "home" button on the remote.
3. select "settings".
4. select "set up" .
5. Scroll down to "factory setting" and restore them.
6. when it asks home or shop display select "home".
ok
Turn demo mode off on
Here'show to turn off the demo mode,
Power ON the television
(Use remote Commander)
1.Select "TV" mode (not AV, demo mode can't switch offwhen you are in AV)
2. Press the "home" button on the remote.
3. Select "settings"
4. Select "set up"
5. Scroll down to "factory setting" and restore them.
6. When it asks home or shop display select "home".
Hi I have a Sony Bravia KLV-40S200A which wont
I had a similar problem with my 42 Inch Philips 42PLF5432D/37 LCD HD TV. It would turn on but then shut back off after about 10 seconds. Then it wouldn't turn on at all. The problem was a bad capacitor. Several bad capacitors. They are inexpensive and fairly easy to replace if you don't mind digging around in the back of your set and soldering some new ones on your Power Supply Board. Or take the less inexpensive route and look for a whole new Power Supply Board. Good luck. Hope this helps.
Antenna unrecognized.
Sometimes the TV will lock out other inputs when a cable is connected. Try the antenna by itself and put the TV in Channel scan mode. If this works reconnect the cable TV cable. If that doesn't work you may need an A/B switch
Sony KDL 40W4500 is 2yrs
Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.
Not finding what you are looking for?