20 Most Recent
Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver - Page 6 Questions & Answers
1 Answer
Drill is smoking
you would probably need to replace the motor, go to Dewaltservicenet.com and type in your model number for a breakdown and also you can order parts from this site. Let me know if you need more assistance.
Dewalt DC920KA...
|
Answered
on Dec 22, 2009
1 Answer
I have a DCD940KX 18v Dewalt drill driver with the
this is not a common problem with dewalt. I have been using them in my construction business for years and only heard of this once or twice. I would go to their web site and get the number for their customer service. They stand behind their products and im sure they will help in every way they can to repair the drill
Dewalt DC920KA...
|
Answered
on Nov 27, 2009
1 Answer
I have a 12v xrp cordless drill. in the past 6
You may want to try a different charger base. Any way you can borrow one so you don't have to purchase first?
If for some reason the charger isn't working well, you may be getting a partial charge and only that.
You may even want to rent a cordless just to try charging your own battery on a different base.
before you buy.
Dewalt DC920KA...
|
Answered
on Nov 03, 2009
1 Answer
How to take my chuck off
The screw that holds the chuck on, is in the bottom of the chuck itself. If there is something jammed in the chuck, it must be removed in another manor. If the chuck is jammed, I have used two pair of channellocks to open the it.
Dewalt DC920KA...
|
Answered
on Oct 07, 2009
1 Answer
The brake does not work
You need a new switch. They are $53 at dewalt. You may also want to check the brushes while you are in there. If they are worn it is advisable to replace them both ($5 each).
Dewalt DC920KA...
|
Answered
on Sep 09, 2009
1 Answer
The drill smokes from the body area when drilling,
It sounds like the motor is burnt up, give me the model number and brand and I will try and find a schematic that will help you. They are not that bad to repair just watch how everything comes apart and pay close attention to the wiring of the switch, it is polarity sensitive.
Dewalt DC920KA...
|
Answered
on Jul 02, 2009
1 Answer
Tools are junk moved on to ridgid
Wait until you have problems with that Ridgid. Parts very hard to find. Ridgid Tools have great threading equipment like the 700 and 300, but their cordless tools are not easy to get help with. DeWalt has a very good warranty program. The dc920's have had a lot of clutch problems and switch recalls, though. Their saws (mitre, circular, etc.) Best in the business. Good luck, friend. Lemme know if you need anything. Please rate me.
Dewalt DC920KA...
|
Answered
on Jun 18, 2009
2 Answers
Drill
Hi hope to help
sounds like you have a problem with your brushes they may just need replacing but do not strip the drill down to do this just take out the batery then take the 4 screws from the rear off the drill and take off the cover see if the brushes are worn it doesnt take a lot of wear to be worn.
You can take off the wire from each brush unit then use a small flat screwdriver to pop out the brush unit then replace you should be able to get the brushes from any dewalt stockest.
Hope that helps. Sean
Dewalt DC920KA...
|
Answered
on May 16, 2009
2 Answers
Drill hole in China Plate
Normally you would use a masonry bit to drill into ceramics eg tiles or bricks. if the plate is glazed it is better to stick some masking tape or adhesive backed paper on the area to be drilled to stop the drill bit slipping around. also i would be inclined to use a hand turned drill or a small battery powered drill if you have one to avoid breakage of the plate.
Dewalt DC920KA...
|
Answered
on May 09, 2009
Not finding what you are looking for?
