Maytag EPIC MFW9700S Front Load Washer - Page 9 - Answered Questions & Fixed issues
I have a f21 code
Hi
F21 error means that the drain time has exceeded 8 minutes; this will turn off the water valves. Press PAUSE/CANCEL two times to clear the display. If errors still remains then please check the drain hose and make sure it is not plugged or kinked. Disassemble the washer by removing the back from the washer and check the electrical connections at the pump and make sure the pump is draining. Also inspect the pump filter for foreign objects. Before disassembling remember to turn off the power and disconnect the washer. If it still doesn't help then there is an issue with the pump and you'll need to replace it.
Hope this helps... Please post back if you need more information.
Daniel
2/16/2011 3:08:36 AM •
Maytag EPIC...
•
Answered
on Feb 16, 2011
•
330 views
Where is the pressure switch hose? and how can you
The pressure switch is located near the top of machine with a Hose connected to it and several wires....You would know if machine is syphoning as it would drain on gravity..Raise hose just in case this will cure.
2/14/2011 11:59:46 AM •
Maytag EPIC...
•
Answered
on Feb 14, 2011
•
73 views
See on control board
The F1 error code indicates that the water level pressure transducer signal is out of range on the machine control board. A pinched or kinked air pressure hose between the bottom of the washer tub and the connection on the machine control board can cause this. A failed control board (the pressure transducer is integrated into the machine control board) can also cause it.
I recommend unplugging the washer and checking the air pressure hose between the bottom of the tub and the machine control first.
2/13/2011 2:01:53 AM •
Maytag EPIC...
•
Answered
on Feb 13, 2011
•
433 views
One piece of clothing every
Hi
The issue seems to be with a worn out belt which is causing
the drum not to spin properly causing this issue. Also check the bellows from
these instructions given by a great tech of FixYa. Hope this helps...please
post back for further assistance.
Daniel
2/12/2011 8:31:15 PM •
Maytag EPIC...
•
Answered
on Feb 12, 2011
•
54 views
F2 warning is displayed what do I do to resolve
Hello,
Welcome to FixYa.
This is a general remedy for most Whirlpool made front-load machines, such as Whirlpool, Kenmore, Maytag, Amana etc. The "Sd" or "F2" is the same as F21 on most Whirlpool washer's and indicates the machine has detected too much soap or a obstruction in the drain process.
Chances are the pump itself is being obstructed by debris or some other foreign object as opposed to being faulty, although the faulty pump can`t be ruled out...yet.
**This is also the reason for a no spin & the "suds" message if applicable**
Here`s how to check it and clean it...
**Turn off the breaker at the service panel or unplug the washer from the wall socket...safety first**
1) locate the screws in front at the very bottom of the panel below the door and pull the panel down and forward until it is off. They will be either 1/4" hex head or #20 torx head screws.
2) You will immediately see the drain pump in front of you with a large removable filter. ( **see image below...this is were a wet-dry shop vac and towels come in handy, also the use of the removed panel as a catch pan is beneficial...but you may still get wet ) 3) Turn it counter-clockwise should allow you to remove it and inspect it and clean it out. Make a good thorough inspection inside the pump as well not just the removable filter.
4) Re-insert the filter and before placing the panel back run a test rinse/drain cycle to inspect for leaks and to verify the unit drains and spins now.
( If the problem still exist`s the Sd or "F2" or "F21" will re-appear. If so you`ll need to check the hose/rubber bellows from pump to tub...back-flow ball...for other obstructions ).
5) If all appears OK after your efforts, well your efforts paid off...pat yourself on the back. You just saved yourself potentially a couple hundred bucks !
Now You should be good to go. Re-attach the lower panel and you`re back in business.
**NOTE: if this still fails to remedy the Sd, F2, F21 or if it returns immediately during the next drain you may require a pump unfortunately...part # 280187 available at "searspartsdirect.com" "repairclinic.com" etc.
**This however can also be caused by the back-flow ball inside the bellows which connects the tub to the pump. There is a large clamp which secures it to the tub, but if you remove it to clean out all the dirt built up inside, make sure you get it good and secure when putting it back.**
Let me know how it goes and if you require further assistance. Thanks for choosing FixYa. Please take a moment to rate the solution provided for you here today. Good luck.
Regards,
Macmarkus :)
6/3/2011 10:55:56 PM •
Maytag EPIC...
•
Answered
on Jun 03, 2011
•
332 views
I have the part, need to replace the "bellows" or
Hi
Please follow below procedure to remove the bellows from your Maytag Front load washer---
1. Unplug washer or disconnect power.
2. Turn off the water supply to the washer.
3. Remove the top cover and the console (see below "To remove the console" for the procedures).
4. Remove the three T-20 hex-head torx screws from the toe panel and remove the panel.
5. Open the washer door.
6. Starting at the bottom, use a small screwdriver, and pry the retaining wire from around the front of the bellows. NOTE: There is a tension spring at the bottom of the wire that can be separated to remove the wire.
7. To remove the door lock/switch assembly:
a) Remove the bellows retaining wire (refer to steps 5 and 6 for the procedure).
b) Pull the bellows out and remove the three T-20 torx screws and flat washers from the door lock/switch assembly.
Door Switch (1 Screw)
Door Lock Switches (2 Screws)
c) Push the switch assembly out of the front panel and then slide the assembly tabs from the connector holder.
d) Disconnect the three wire connectors from the switch terminals and remove the assembly.
8. To remove the front panel and bellows:
a) Remove the top cover and the console (see below "To remove the console" for the procedures).
b) Remove the bellows retaining wire (refer to steps 5 and 6 for the procedure).
c) Pull the bellows off the lip of the front panel.
d) Remove the door lock/switch assembly (see step 7).
e) Close the washer door.
f) Remove the four T-20 hex-head torx screws from the top and bottom of the front panel and remove the panel from the unit.
g) Remove the end of the dispenser tube from the bellows.
h) Use a 7mm socket, and turn the bellows retainer clamp screw counterclockwise until the clamp is loose enough to remove from around the bellows.
i) Remove the bellows retainer clamp.
j) Remove the bellows from the front of the tub.
a) Lift the locking tab and disconnect the ribbon cable connector from the central control unit.
b) Remove the ribbon cable from the five clips.
c) Pull the detergent dispenser drawer out as far as it will go, then press down on the release tab, and remove the drawer from the unit.
d) Remove the T-20 torx screw from the recessed hole of the console.
e) Press the locking tab on the right rear side of the console, and pull out on the console to disengage the tab from its slot.
f) Pull out at the bottom of the console and lift it to unhook the top edge from the cabinet, and remove the console.
To remove the touchpad / LED assembly:
a) Use a small screwdriver and unsnap the three top locking tabs from the touchpad/LED assembly.
b) Starting from the right, unsnap the four lower locking tabs from the touchpad/LED assembly, and lift the assembly from the console. NOTE: If the pushbuttons are attached to the assembly, unsnap them from the old assembly, and install them on the console at their correct locations.
Hope this helps...
Danil
3/1/2011 11:43:45 PM •
Maytag EPIC...
•
Answered
on Mar 01, 2011
•
107 views
My epic front loader is
OH,OH!!!, I think the main bearing is bad on the washer, see if the inner tub has play by moving it up and down. even if is not I'm sure the bearing is bad. with time and clothing weight the water seal worn allowing water to wash the lubrication in the bearing. this is a mayor repair.
2/9/2011 2:08:25 AM •
Maytag EPIC...
•
Answered
on Feb 09, 2011
•
260 views
My maytag epic z is
Give this a shot:
http://www.fixya.com/support/t4027040-error_code_f21_will_not_spin_maytag_epic
2/6/2011 3:00:40 PM •
Maytag EPIC...
•
Answered
on Feb 06, 2011
•
332 views
I'm looking for a video to replace a snubber in my
I'm assuming that since you mentioned a "snubber" that the washer you are referring is a Maytag manufactured top loader (Admiral is manufactured by Maytag). If so, the following link can give you some guidance on how to repolace the snubber and/or brake assembly:
http://www.fixya.com/support/r3574320-maytag_washer_squeaking_problem
I have included part numbers for tools you may need and some advice on what you can do to avoid having to purchase any higher priced special tools.
Replacement parts (if required) can be purchased at any of the following web sites:
searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com
Recommendations on parts that may require replacement:
Brake Rotor with Lining
Brake Stator
Snubber
The part numbers will be based on your MODEL NUMBER.
Prices will vary between the sites I have listed, so shop and compare. The first three sites I have listed, have helpful exploded view diagrams to assist you with locating and properly identfying the parts you need. If you search by model number, these parts are listed under the "Transmission" parts list. This is not a difficult repair, and the parts (including most of the tools) are not expensive.
If you have any questions about this repair, please post back and let me know. I hope you find this information helpful.
2/4/2011 12:59:39 AM •
Maytag EPIC...
•
Answered
on Feb 04, 2011
•
292 views
My washing machine has a light on on the front
Press and hold the botton that says control lock on or off////be about 3 seconds might be two buttons at one time//that will unlock the control....good luck please vote...............thank you
2/2/2011 10:45:07 AM •
Maytag EPIC...
•
Answered
on Feb 02, 2011
•
48 views
Not enought water during wash .water supply normal
Hi from retired Englishman in SW France @16:44 Sat afternoon!
Do not hesitate to use the new machine warranty- that is what it is there for!
It should not cost you anything. If it does it is not a good warranty/manufacture/retail outlet!
Cheers,
John C
1/29/2011 3:48:16 PM •
Maytag EPIC...
•
Answered
on Jan 29, 2011
•
57 views
DISHWAHER WONT COMPLETELY DRAIN ALL
drain hose is to low to sink connection zip tie side connected to sink up towards bottom of cabinet top so water dosent backflush into dishwasher from sink draining
1/27/2011 3:26:55 AM •
Maytag EPIC...
•
Answered
on Jan 27, 2011
•
70 views
Maytag clothes washer vibrates excessively
Hi,
When my washer did that, I found that the shocks that hold the tub were bad...
Check out this tip I wrote about the noise and vibration that front load washers can make..
Washer Problems Washer noise when spinning
heatman101
1/25/2011 9:46:02 PM •
Maytag EPIC...
•
Answered
on Jan 25, 2011
•
441 views
Having major problems installing the bellow on my
To
get the clamp back on you'll need to fit the rubber part on first.
Then begin working the wire part of the spring clamp back on, starting
180 degrees away from the spring. As you work it back on and into the
groove, it will become harder to get on. When you can't go further,
carefully lever the wire and spring over the lip and into place with a
small screwdriver, or similar, being careful not to pinch or tear the
rubber bellows.
Best regards,
--W/D--
1/24/2011 4:29:22 AM •
Maytag EPIC...
•
Answered
on Jan 24, 2011
•
148 views
Need instruction on how to
The boot will have a retaining wire on both the front panel and plastic tub interfaces. You need to remove the front panel wire first. Simply pull the lip forward until you can see the wire. Use a pliers or screwdriver to remove it. Peel the boot off of the front panel and you can see the attachment to the tub. Same removal technique.
Be very careful when installing the new boot to be sure it is seated fully and correctly all the way around the tub. Reinstall the retaining wire. Same installation technique for the front panel.
Good luck.
1/22/2011 1:33:19 PM •
Maytag EPIC...
•
Answered
on Jan 22, 2011
•
153 views
It flash 2 then 0
F20 error code indicates no water detected entering the washer. Be sure the drain hose is not down too far into the drain stand pipe & both hot & cold water is turned on & working.
1/18/2011 2:56:45 AM •
Maytag EPIC...
•
Answered
on Jan 18, 2011
•
205 views
When washer starts to wash it beeps and flashes
Hi
Error FH means that a water inlet problem has occurred. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. Press PAUSE/CANCEL twice to clear the display. If the machine is not filling then check whether both valves at water source are turned ON and inlet hose are not plugged. If the machine is filling fine then chec the pressure switch hose and the drain hose for siphoning (also make sure water is not flowing back to the machine from drain hose). Check wire harness connections to: Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU). Hope this helps... Please post back if you need more information.
Daniel
1/17/2011 8:37:05 PM •
Maytag EPIC...
•
Answered
on Jan 17, 2011
•
192 views
Not finding what you are looking for?