Bosch Nexxt 100 Series WFMC1001UC Front Load Washer - Page 8 - Answered Questions & Fixed issues
When I turn the washer on any cycle to wash all
I suspect that the controller board is defective and a possibility that the microcontroller is faulty.
Since the main board is filled with epoxy it will be difficult to identify the component as the testing becomes tiring.
Look for any chance that the board has any visible damage, any power related issues. If not the board may need a change.
Finished, wash and spin lights flashing. Door
I just had this problem! To get the clothes out, open door manually (follow answers on other threads here about opening toe panel and gently pulling down on door release). But as it turned out, I didn't need to remove the clothes, and now my washer is working again.
A local repairman gave me this advice over the phone. Make sure dial is switched to off. Unplug your machine, then plug it back in. Hold down the rinse and delay buttons with one hand. With the other hand, switch the dial from off to cold or warm or whatever cycle you want. All the buttons flash a few times, then just the start button flashes. The second time I tried this, my washer worked afterwards. I've done several loads today with no problem.
Bosch Nexxt 100 series washer stops at 1st spin cycle
take a look at your manual that came with your machine go to problems usually at the back and see what that says,or go to the bosch website and type in your model number its on the inside of the door.i would suspect a program fault.adrian,,,,,
Washer not draining
Probably the pump filter needs cleaning.
It should be located at the bottom front of washer behind drop down cover, turn anti-clockwise to remove and clean.
The door is locked and won't open
Normal
0
false
false
false
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
This is for the WFMC6400, but it could help.
To manually unlock the door lock system, perform
the
following steps:
1. Unplug the power cord from the outlet.
2. Remove the lower toe panel.
3. Reach up along the inside of the front panel and
locate the bottom of the
door latch assembly.
4. Located on the bottom of the door latch
assembly is a teardrop shaped tab.
Gently pull the
tab down approximately 1/4 inch,
or until a click is heard.
5. The door may now be manually opened.
Pl give me a ‘very helpful’ rating for the free
help,
thanks!
Clothes in door locked, beeps and will not start. panal lights o
Normal
0
false
false
false
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
This is for the WFMC6400, but it could help.
To manually unlock the door lock system, perform the
following steps:
1. Unplug the power cord from the outlet.
2. Remove the lower toe panel.
3. Reach up along the inside of the front panel and
locate the bottom of the
door latch assembly.
4. Located on the bottom of the door latch
assembly is a teardrop shaped tab.
Gently pull the
tab down approximately 1/4 inch,
or until a click is heard.
5. The door may now be manually opened.
Pl give me a ‘very helpful’ rating for the free help,
thanks!
My bosch nexxt wont drain and flashes e04 checked
The 03 error code is the drain. Disconnect the drain hoses
and check for blockages. If no blockage "time" the drain interval. If
it's more than 6 minutes it's the pump. Also make sure you're using the
correct
type of soap so the ball check valve on the bottom of the outer drum
isn't
getting fouled with excessive suds. Also disconnect the drain hose from
your
house plumbing and let it free flow on it's own. This will tell you if
the
block is in your plumbing, and not in the machine. Assuming that your
filter is clean.
Pl rate me ‘very helpful’ for the free help!
Washer will not drain
There may be more debris in there or the impellor is now broken from its shaft,the pump will need replacing.
Washing cycle works, but when starts spin cycle it
Have you checked the lid switch? There should be a tab on the lid that presses into an opening. The opening contains a switch that lets the machine know that the lid is closed. Try to push it in with a screwdriver to see if the spin cycle starts. The switch could be damaged even if the tab, or screwdriver can press it in.
Panel lights are on. push on button nothing
I have experienced the same thing a number of times. To solve, open the door, then turn the knob, and push the start button on and off, and push the delayed start button (3, 6, 12 hour). Then close the door, and retry. This routine seems to reset the system.
Bosch 100 series will not drain
You need to check and clean the pump filter if you have not already done so.
This is located at the bottom front right of washer.
Unscrew anti-clockwise to remove and clean.
How to raise the water level in a nexxt 100 series
Water level is set according to the pressure system within the machine and this is not adjustable, One thing to make sure of is that your waste pipe is not pushed to far into the drain pipe as this may cause sythoning, and thus you are in fact loosing water via drain pipe
Softener dispenser will not drain properly.
you may need to just remove the cup and give it a good clean this will normally do the trick. when you have removed the cup there is normally a small hole underneath, make sure this is clear, I normally use small piece of wire
Not finding what you are looking for?