20 Most Recent Kyocera Copystar CS-1820 Black and White Copier - Page 6 Questions & Answers

simple, clean the waste toner simples, limpe o reservatorio de toner usado.http://www.youtube.com/watch?v=oMysn3Jnpts

There is no way to fix this yourself, a part will not be available for the repair.
Better have a service guy do the fixing for the issue, and for proper mending on the damage., tried searching for documentation regarding your concern but no manual is available online, call the manufacturer for best results.

If not found on the list update windows and it will appear on the new list

Hello rsly,
First of all, you need to be sure that the toner cartridge was installed properly. If it was installed properly, then it will first print out with excess toner on paper and thecopies will look bad before it actually starts printing normally. The printeris just getting the toner properly set by pushing out the excess toner and leveling the cartridge.
If you followed these steps when installing the toner cartridge, you are on track:
Open the door in the printer or copier that contains the toner cartridge. This is usually located in the front of the machine. Pull the entire drum unit out of the machine.
Place the drum unit on a sheet of paper or a drop cloth to catch any toner that might spill. Make sure the area has no wind or open flame, because you are dealing with a flammable powder.
Disconnect and remove the old cartridge from the drum unit. Hold down the lock lever on one side of the unit that holds the cartridge in place and pull the cartridge out with your free hand.
Remove the new toner cartridge from its packaging. If the cartridge comes with an aluminum bag, place the old cartridge in the bag and dispose of it as your local laws and ordinances require.
Rock the new cartridge gently to each side to make sure the toner is distributed evenly. Remove the protective cover from the cartridge, which is a flat rectangular bracket clipped onto one end of the cartridge.
Insert the cartridge into the drum unit in the same manner the old cartridge fit into it. The cartridge will "click" into place and the lock lever will automatically lift up.
Clean off the corona wire in the drum unit. There is a tab at the end opposite from where you inserted the cartridge. Slide this tab to the right and left several times and then place the tab back into its "home" position.
Load the drum unit back into your printer or copier and close the cover.
Now for the door, it does not seem to carry too much effect during the printing process, it is for the unit not to be looking too messy. There must be something that is not in place for the door not to be covering the way it is meant to. Check for where the springs are meant to be seated and resit it there properly and be sure to check if there is nothing broken on the door.
Hope this information helped. Goodluck Elect_Comp

To Reset the Toner Gauge

1) Press System Menu/Counter
2) Scroll to 'Copy Setting' and Press ENTER
3) Scroll to 'Toner Setting' and Press ENTER
4) Scroll to 'Toner Gauge Reset' and Press ENTER
5) 'Are You Sure?' is displayed then Press LEFT SELECT

If you need any further asistance then please just ask.

Try to re install the cartridge? Also make sure the drum unit & developer unit are connected corretly. Odds are one of the two clips that lock the two parts of the drum unit may be broken....

Sensor in feeder is probably broken. To get around this until you can get it fixed power down the unit and unplug it. Unplug the cable that connects the Doc feeder (in the back) to the main unit (two screws hold it on. Then power the unit back up it will work with out the Doc feeder. You will just have to put the copies on the main glass.

Two way to scan to the computer from this model from the USB or the ethernet connection. It depends on how the computer is connected to the computer. If you are connected through the USB than TWAIN scanning is what you will be using. You will need to go to this link to download the driver.

http://usa.kyoceramita.com/americas/jsp/Kyocera/download_center.jsp?pid=14173&pcat=10564&rcid=10009&rscid=10996#bottom

Just copy and paste that link. With Twain scanning you will need a photo edit program to pull the pic into your computer. As for the network scanning using the network port just ask how to scan using the network port that is another beast altogether. Hope this helps.

service mode is 10871087

JAM 40 is a fuser jam. Remove the process unit and make sure there is no paper there. Open the back cover and make sure there is no paper there. Turn the machine off then back on. If you are still geting Jam 40 then you have a bad sensor or similar issue.

Is this printer installed on a server and shared over a network? Or is it installed independently on each workstation?
If it's on a server, printing could be "paused", or set to "use offline" Go to the "printers and Faxes" dialog box, and 'right click" on the printer icon, is there an option to either "resume printing", or "use printer ON line"? If so, select this option.
If it's not on a server then it would be extremely unlikely that this condition would happen on all workstations
Other than that make sure that the Subnet mask is set correctly on the printer.
If that doesn't work....it's probably time to try re-installing the driver.

In your machine there is some short circuit for the AC supply , and we can expect the fuse on the power supply boarad has been failed or the ac powersupply it self became defective if you removes the ac power supply and give it to any electronic shop shop they can repair it but you have to find the short circuit first probably on fuser module or exposure lamp unit, rate this and if you have any queries you can ask me

SIM 163 Reset (only do this one SIM, by doing others you could cause your machine to no longer function). Also see note at bottom.

1. Press the system menu/counter key.

2. Select Service setting using the up/down cursor keys.

3. While pressing the start key and the # key, press the enter key. (Maintenance mode is entered.)

4. Select Maintenance mode using the up/down cursor keys.

5. Press the enter key.Enter the maintenance item (163 Resetting fuser problem) number using the up/down keys.

6. Go to step 1 under method below.

Resetting the fusing problem data Description

Then, turn the power switch on and press the system menu/counter key to enter the maintenance mode.

Purpose

To prevent accidents due to an abnormally high fusing temperature.

Method

1. Press the enter key. A selection item appears.

2. Select Execute using the up/down cursor keys.

3. Press the enter key. The fusing problem data is initialized.

Completion

Press the back key. The indication for selecting a maintenance item No. appears.

Note:Sometimes in order to do the reset when the machine is in an error state you need to open the top cover (like to replace the toner) and leave it open until you have performed the reset.

SIM 163 Reset (only do this one SIM, by doing others you could cause your machine to no longer function. Also see note at bottom.

Entering Simulation Mode

1. Press the system menu/counter key.

2. Select Service setting using the up/down cursor keys.

3. While pressing the start key and the # key, press the enter key. (Maintenance mode is entered.)

4. Select Maintenance mode using the up/down cursor keys.

5. Press the enter key.Enter the maintenance item (163 Resetting fuser problem) number using the up/down keys.

6. Go to step 1 under method below.

Resetting the fusing problem data Description

Resets the detection of a service call code indicating a problem in the fusing section.

When a service call concerning the fusing section occurs, turn the power switch off and open the front cover.

Then, turn the power switch on and press the system menu/counter key to enter the maintenance mode.

Purpose

To prevent accidents due to an abnormally high fusing temperature.

Method

1. Press the enter key. A selection item appears.

2. Select Execute using the up/down cursor keys.

3. Press the enter key. The fusing problem data is initialized. (Four service calls, namely C6000, C6020,C6050, and C6400 are reset.)

Completion

Press the back key. The indication for selecting a maintenance item No. appears.

Note:Sometimes in order to do the reset when the machine is in an error state you need to open the top cover (like to replace the toner) and leave it open until you have performed the reset.

It sounds like you have a bad control board or EEprom.

C7990 is

Waste toner reservoir overflow problem (when the total number of copies is 100 thousand sheets or more)

• After E31 is displayed, 1,000 sheets are copied. Or waste toner exceeds 5 g.

Defective waste toner sensor or engine board (KP-5061).

Shake the process unit from side to side and turn the power switch off and then on. If the problem cannot be solved, replace the process unit. After replacing the process unit, turn the power switch off and then on. If the problem

cannot be solved, replace the waste toner sensor or the engine board (KP-5061).

I hope this is helpful,

Shawn

Take out the drum unit and remove the shutter. (Temporarily). Then order a new imaging unit

C6400 is a fixing unit error. You may need a new fixing unit but most of the time it can be reset in maintenance mode.

Use the following steps to enter the maintence mode, once there follow the steps for maintence mode 163 (reset fuser error). Do not do anything else in the maintenance mode area because you could damage your machine

Press the system menu/counter key.

Select Service setting using the up/down cursor keys.

While pressing the start key and the # key, press the enter key.

Select Maintenance mode using the up/down cursor keys.

Press the enter key.

Enter the maintenance item number (163) using the up/down keys.

Press the enter key.

1. Press the enter key. A selection item appears.

2. Select Execute using the up/down cursor keys.

3. Press the enter key. The fusing problem data is initialized. (Four service calls, namely C6000, C6020, C6050, and C6400 are reset.)

Completion

Press the back key. The indication for selecting a maintenance item No. appears.

Turning power switch off and back on

Resetting the fusing problem data

Description

Resets the detection of a service call code indicating a problem in the fusing section.

When a service call concerning the fusing section occurs, turn the power switch off and open the front cover.

Then, turn the power switch on and press the system menu/counter key to enter the maintenance mode.

Purpose

To prevent accidents due to an abnormally high fusing temperature.

Method

1. Press the enter key. A selection item appears.

2. Select Execute using the up/down cursor keys.

3. Press the enter key. The fusing problem data is initialized. (Four service calls, namely C6000, C6020,

C6050, and C6400 are reset.)

Completion
Press the back key. The indication for selecting a maintenance item No. appears.

Turning power switch off and back on.

I hope this is helpful,
Shawn