Top 20
Mitsubishi WD-52531 Television Questions & Answers
Need remote control
go to www.tvassist.co.uk if its not listed they will almost certainly still stock it call them and ask them to list it and they will
8/28/2013 7:50:02 AM •
Mitsubishi...
•
41 views • 0 helpful votes
No picture
Lamp life for this model is 2 years or 2000 hours, less if a non Mitsubishi lamp is used, sounds like a bad lamp.
12/22/2012 7:43:30 PM •
Mitsubishi...
•
50 views • 0 helpful votes
Hered a pop sound and now tv wont work
From what I researched, after changin a bulb on these TV's some capacitors fail and "pop" on the DM board, You will have to take it apart and re-cap the caps on the DM board 1000uf 10v (4 - 7 of them). This solves the problem in most cases
4/24/2012 9:05:52 PM •
Mitsubishi...
•
143 views • 1 helpful votes
WHERE CAN I FIND THE BALLAST IN THE MITUSUBISHI WD 52532 MODEL
hint: the two pins the lamp plugs onto go directly to the ballast which is really a power supply for the lamp.not clear from all you have said if ballast is the problem===these sets had a lot of issues; anything, even too much dust on the fans inside will shut it down...........
3/26/2012 4:48:48 PM •
Mitsubishi...
•
208 views • 1 helpful votes
It turns off and an
Hi,
Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.
i hope this will help to solve the problem...
8/6/2011 5:43:21 AM •
Mitsubishi...
•
192 views • 0 helpful votes
The lamp light is blinking
You may have not plugged the lamp in fully or have not put the lamp door back properly. If you have done this properly and have the blinking problem then you are likely to have a bad ballast. This ballast supplies the voltage to light up the lamp. But first look on the front of the set for a small push button that says "system restore/reset". Use a ball point pen to press.
6/28/2011 5:22:08 AM •
Mitsubishi...
•
529 views • 2 helpful votes
I have a Mitsubishi DLP
Did you try the soft reset?
With the set on and using the Mitsubishi remote: Menu, 1,2,3 and Enter.
SD TECH
6/3/2011 3:55:34 PM •
Mitsubishi...
•
251 views • 0 helpful votes
Blinking orangr lamp light
It is time to change the lamp.It is building up internal resistance and it will get to the point it will not come on at all, change the lamp.
5/2/2011 4:14:07 PM •
Mitsubishi...
•
279 views • 1 helpful votes
My WD-52531 is darker in
hello,
Try first cleaning all the lenses from inside the TV'S projector DLP projection TV's are very prone to dust accumulation because of spinning mechanical and lenses..To do the cleaning you need to open the back cover of your TV use a soft cloth to wipe all the dirt and dust from the lenses be carefull not to apply a force you might break the lenses.clean also the projection lamp.you can also replace the lamp if the lamp is not bright or nearly to be busted.....do first the cleaning and lets see if this resolve the problem....good luck and please post back if you need further assistance...
4/4/2011 9:56:01 PM •
Mitsubishi...
•
157 views • 1 helpful votes
Wd-52531 color is being overpowered
Hi, You are most likely seeing the effect of a defective optical engine. This is the part that processes and projects the picture onto the front screen. Physical anomolies can cause random blobs of colors and a distinct appearance of haze in the center of the pic. The only fix is to replace the engine, usually around $800 to $1000. THX
Bill W.
integrityhomeworx.com
3/7/2011 3:42:10 AM •
Mitsubishi...
•
334 views • 1 helpful votes
TV turns on for about a minute, then goes
That is the sound of the power relay being disengaged by the protection system of the power source which has detected a lower than normal value on one of its outputs but gets reseted every single time when the power is cut so it just cycles. This happens when a major components fails - in your case the most likely part that failed is the ballast board. To confirm that you must open the tv and test the voltages on the power source and the ballast board. This is a job for someone with at least a basic experience so it's time to call one.
11/1/2010 9:01:31 PM •
Mitsubishi...
•
186 views • 0 helpful votes
TV shut off and red light came on
Hi,
Question shows it is Mitsubishi WD-52531 tv, if that is right then let me know when did you replaced its lamp last time?
It sounds lamp is dead in this tv and need to be replaced.
Lamp replacement procedure is written in user manual and its easy.
Let me know if you have additional question.
Thanks.
5/22/2010 10:26:07 PM •
Mitsubishi...
•
261 views • 0 helpful votes
Not finding what you are looking for?