20 Most Recent
LG WM2016C - Page 4 Questions & Answers
I wash my white together
Try spining it with vinegar and let it dry then see what results u have after the spin
5/7/2011 4:06:21 PM •
LG WM2016C
•
Answered
on May 07, 2011
WM2016CW will not go into spin cycle. Makes
I'm having the same problem with mine. The washing machine was given to me because the people who had it kept getting this problem. If the tub clean cycle isn't ran on a normal basis then this will happen and I would assume you have seen the LE code pop up on the display. If the normal maintenance is run and the problem is still present then the problem could be a bad tub bearing. First thing to do is run the tub clean cycle with very little bleach and make sure to use normal bleach and not anything like ultimate care bleach as to avoid suds. Just make sure to use a small amount and let it run.
5/1/2011 3:34:40 PM •
LG WM2016C
•
Answered
on May 01, 2011
I have a wm2016cw washer
Here is the knowledge base information. http://lgknowledgebase.com/kb/index.php?View=entry&EntryID=6273
If you check all these, and still getting the error, you'll need to get the drain motor replaced. This is not a simple task, as the entire front of the unit must be removed to access the drain pump area.
Top must come off, control panel detached, door gasket outer ring needs to be removed, door lock also much be unplugged. The front panel of the unit also needs to be removed as well.
3/14/2011 1:27:43 AM •
LG WM2016C
•
Answered
on Mar 14, 2011
Washing mating won't start
That is fortunate as you don't want a lot of unwanted baby washing crawling around. Come the spring, which is the washing mating season, keep a close eye on the washing and I'm sure the mating will start!
Any clue like an error code?
I hope I have been of help but please do not hesitate to ask if you have any further questions.
I appreciate your vote if you appreciate my reply.
2/24/2011 8:43:13 PM •
LG WM2016C
•
Answered
on Feb 24, 2011
How do I get the
On the back of the washer's top you will find two plastic parts. Remove the bottom screw from each of them. Now, stand in front of the machine and use the palms of your hands to sharply push the top back (about two inches), then, lift the top off.
1/31/2011 7:55:57 PM •
LG WM2016C
•
Answered
on Jan 31, 2011
During spin it vibrates alot
Hi there and welcome to fixya,
There's a problem with the alignment. First step is to make sure the machine is on a leveled ground. second procedure would be to check if the belt alignment is misguided but this requires you to open the machine. If you're not into servicing, it would probably best to ask experienced people open the machine and check for any misalignments inside.
Hope this helps,
levibit
12/22/2010 7:48:44 AM •
LG WM2016C
•
Answered
on Dec 22, 2010
Water leaking under the washer?
Take the bottom off by removing the 3 screws. Check to see where the water is coming from. It could be the pump or something as simple as a hose.
11/26/2010 9:29:59 PM •
LG WM2016C
•
Answered
on Nov 26, 2010
On the spin cycle setting,
It blinks when you have spinsense mode activated. When you first start a load just press and hold the water plus button for 3 seconds to turn it on and off. I'm honestly still not sure what exactly the spinsense mode does but thats all it is so nothing to worry about.
11/7/2010 11:59:15 PM •
LG WM2016C
•
Answered
on Nov 07, 2010
Drain plug tubing has a long cut in the tubing,
The tubing comes out of the pump on the opposite side of where it exits the front of the machine so it's in a U shape. There's a bracket inside that helps in preventing the tube from kinking but unfortunately can also cut the tubing if it snags it. I would imagine that something like this was the cause.
11/7/2010 11:45:21 PM •
LG WM2016C
•
Answered
on Nov 07, 2010
LE code comes on-I followed tip of turning wm off
Had the same problem myself. The LE code is a motor fault and I found the rotor magnets and stator coils to have areas with thick layers of oxidation. I removed both and cleaned with a wire brush but with the stator it should be the top end that the rotor magnets face so don't take the wire brush to the copper windings. Apparently at some point my washer was leaking at the water supply connections and although this was a very small leak overtime it adds up and it happens to drip directly above the rotor. I sealed the open edges of the water supply box with electrical tape to prevent water from dripping in just in case it ever leaks again.
11/6/2010 6:54:45 PM •
LG WM2016C
•
Answered
on Nov 06, 2010
My machine is leaking from
Unplug the machine, Take off the back access panel cover and see if you can see anything... Just be careful inside of cabinet has lots of sharp edges and such. Let us know if we can help with anything else
11/3/2010 4:04:45 PM •
LG WM2016C
•
Answered
on Nov 03, 2010
Not finding what you are looking for?