20 Most Recent
LG WM2016C - Page 6 Questions & Answers
I have never liked my lg and now it seems that
You might check the water inlet valve on the back of the machine where the water hooks up. There should be a blue plastic water valve. remove the water hose on both sides hot and cold. At the blue water inlet valve inside the connector there are small filtering screens (similar to an areator valve on your sink faucet) They may be clogged by sediment and this would cause your low water issue and possibly the smell. Simply pull out the screens with a pair of needle nosed pliers and replace. Hope this helped
Dave
11/5/2009 12:46:20 PM •
LG WM2016C
•
Answered
on Nov 05, 2009
The lights on my LG WM2016CW will not come on.
While looking for the fuse, which I could not find despite opening up the machine from the back (and vacuuming underneath--yuck!), I left the washer unplugged for about 30 min. From reading other forums and such, I realized that unplugging for a little while is often the solution because the prolonged (at least 5 min) lack of power triggers the system to reset. Sure enough, when I went back to plug it in and give up for the night, the thing worked fine. Good luck to anyone else out there!
8/24/2009 3:56:57 PM •
LG WM2016C
•
Answered
on Aug 24, 2009
Washing machine will not drain. water wont drain
If your washer won't drain, check these:
It spins, but doesn't pump
It doesn't spin or pump
It pumps, but the water returns
It spins, but doesn't pump
If your washer spins but doesn't pump the water out, the drain line is probably clogged. In many washers, a small sock or other piece of clothing can get between the clothes tub and the outer tub that holds the water. If the clothing gets between the tubs, it may then get into the drain hose that's attached to the pump--or even into the pump itself. If it's in the pump, you need to remove the hoses from the pump and pull the item out.
To remove the sock from the outer tub port, open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then, using needle-nose pliers, try to grab and remove the clothing through the port.
Sometimes you can't remove the stuck clothing from below. Then you have to remove the agitator, top of the outer drum shield, and inner clothes tub. This isn't easy to do--and you may need special tools--so you might be happier getting a qualified appliance repair technician to do the job.
If the drain line isn't plugged, the problem may be with your pump. Even if the pump appears to be turning, the internal impeller may be broken. If so, you need to replace the pump.
It doesn't spin or pump
If your washer doesn't spin or pump water out but the motor is running, your washer probably has a frozen pump pulley. If so, you need to replace the pump. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it.
It pumps, but the water returns
If the water that pumps out of the machine goes back into the machine after the spin cycle, your washer may be siphoning the water from a laundry tub that has a slow drain, back into the washer. The usual remedy for this is to improve the draining of the laundry tub. (Is something stuck in the drain?) Also, check for these problems:
- If the drain hose reaches more than about 4 inches into the laundry tub, cut off the excess.
- If your drain hose is lower than the washer's cabinet, install an air gap/siphon break assembly.
8/20/2009 4:29:47 AM •
LG WM2016C
•
Answered
on Aug 20, 2009
Lg washer smells like rotten egg.
go buy a small bag called "shock" for a pool.. it is only $3 at home depot.. just add 1/4 cup on an empty cycle with hot water.. it will scrub your plastic and stainless clean.. i have my wife add a teaspoon to all my clothes.. our towels would smell moldy a couple hrs after getting out of shower. now they have no smell anymore.. no smells comming out of washer either..
7/7/2009 6:41:23 AM •
LG WM2016C
•
Answered
on Jul 07, 2009
My washer will not turn on. We had an uneven load
Do you have the owners manual? Look in there for any reset info. Check to see if the circuit breaker for the power outlet popped. Try unplugging the washer and then wait a minute and plug it in. If the motor got hot it might have a reset button on it.
6/25/2009 5:25:40 AM •
LG WM2016C
•
Answered
on Jun 25, 2009
Error code-OE
Hi there,
OE-pump blocked. Disconnect the power before attempting any work. Use of an RCD (plug in power breaker) is recommended.
Disconnect pump from sump hose and check for obstruction in either item. Pump removal: power off, remove cover, locate pump, (attached to other end of drain pipe).undo 2 wiring connections, 2 hose connections, and pump mounting screws. Remove pump chamber - some are held in with screws, others clip into place. Check for foreign objects round the impeller. If pump chamber is clear, may be a fault with the pump motor - in which case, replace.
Also check the filter - generally located behind a panel at the foot of the machine.Some are obvious like little square hatches and some are hidden behind the trim panel at the foot of the machine. Once panel is removed the filter should be visible. Its generally a circular plastic fitting which unscrews in an anticlockwise direction. Some hotpoint, indesit and ariston filters are located in the big black sump hose (the one that leaves the bottom of the outer drum and connects to the pump). Remove the back cover, locate hose, remove the tensioner clip by squeezing the tabs together, remove the hose, take out filter and clean.
Good Luck!!
5/6/2009 2:47:39 PM •
LG WM2016C
•
Answered
on May 06, 2009
Replace Clamp Assembly on door to LG WM2016CW front load washer
Any apliance repair store there is a store that is called Marcon that sells tools and appliance parts. but really all you need is a good pair of vise grips. It is a royal pain to replace the door seal. The only way that i can replace this is to take the whole front panel off. takes me aboutt 2 hours to replace without any special tools just vise grips
1/5/2009 4:29:05 AM •
LG WM2016C
•
Answered
on Jan 05, 2009
Serial Number location on LG WM2016CW
Serial number will be something like:
804KWLL10010
(The first three numbers are a manufacture date code, the next two letters will be manufacture location code.)
1/4/2009 8:03:28 PM •
LG WM2016C
•
Answered
on Jan 04, 2009
Machine doesnt start. the wash and spin indicator lights blink alternating
first try unplugging and waiting a minute and then plug in and see if that resets it. if it does not try unplugging, wait a minute, hold power button in for 15 secs and then plug back in and see if that resets it. and finally, try the second one and continue to hold power button in while plugging back in. all are different ways of resetting some washer models. one might work for you and cannot hurt to try. good luck
LG Fuzzy Logic 8.2 kg top louder WF-8071TTP
This dE error or fault code to indicate that the door is not latching properly. Check the lid or door operation to be sure it's not binding and that the door alignment is correct. Also, check the door/lid hinges to be sure they're not binding. Finally, make sure the door catch is in place and not broken. You may need to replace the door hook/catch or the door lock assembly.
LG error code
its best to get an engineer to the problem as it could be anything at all or just an alignment problem eric
Not finding what you are looking for?