Sennheiser HDR 130 Consumer Headphones - Page 3 - Answered Questions & Fixed issues

There's an auto-shutoff feature which kicks in when the audio input to the transmitter is too low. That's usually indicated by the green light on the transmitter turning off. Just increase the volume on the device connected to the transmitter, and you should see the green light come back on. As long as that's on, it'll stay transmitting.

There's an auto-shutoff feature which kicks in when the audio input to the transmitter is too low. That's usually indicated by the green light on the transmitter turning off. Just increase the volume on the device connected to the transmitter, and you should see the green light come back on. As long as that's on, it'll stay transmitting and shouldn't just shut off.

I thought this was another example of the proprietary world of Apple, whereas any non-Apple made or certified headphones/headsets with mic and/or volume control will not work with an iPhone or iPad (I am not sure about iPod). It took me many headsets to figure out what was going on. However, your headphones seem to be made for iPhone and sold in Apple stores. If this is the case, I will go back to any Apple store and talk with the tech people there about your situation.

Probably yes, connecting the RS transmitter to the composite audio output jacks (L/R) on the back of the Vizio TV.

I hope this may help you.. https://www.youtube.com/watch?v=jWx6rX434CM visual is always my best teacher.. if not then refer to the manual http://cdn.vizio.com/documents/downloads/hdtv/M320VT/615M320VT%20User%20Manual.pdf

If it always is on the same side, check your hearing..could be that you may have diminished hearing on one side

you have to unsolder the wires on the coil assembly then pull everything out through the bottom. replace the bad wire, reassemble the xlr end and resolder the wires to the coil.

I assume you mean the mic plug/jack. Bent pins or broken connectors will require a new jack and/or plug installed and they are not easy to do. These 3.5 mm jack connectors require both a light touch during install and soldering. If you're a pro then start shopping for a replacement 3.5 mm mono jack but be warned. The jack may solder directly to the PC board....which reminds me. Look for broken connections from jack to PC board..a common failure point and resolder as needed.

This doesn't sound good...mic cartridges are pretty fragile and is why I recommend buying quality mic's so that a few "drops" won't change the sound. That being said, the Sen MD431 is over $400 which should mean either you gave it one heck of an impact, or the mic has a manufacturing defect. Try returning for factory service BUT request an estimate B-4 repair.

Adjust mixer boa If you need further help, I’m available over the phone at https://www.6ya.com/expert/richard_b59056c0c62ecb00

you might check to make sure that your gain isnt to high many times this can negatively effect your sound quality

The mic likely requires professional service.

Never used them, but distorted outputs indicates you are over-driving them, connected them to 'speaker out' rather than 'headphone out', Or you have already blown the drivers. Connect to a different sound source and see how they work then. You likely will not get a loud boom from any headset.

get new earphones those are cheap or you can adjust the head phone volume in the ipod or iphone in setings

need more information.what model?handheld or beltpack? microphone or instrument?check transmitter and receiver are set to same frequency.does a different transmitter work with the receiver?does the receiver show the transmitter is functioning (ie receiving rf) but not receiving audio signal (af)?

You should be able to hook the tv to the cable box the cable box should have your A/V jacks. If so unplug the PS3 plug in your receiver to the cable box and run the PS3 through the receiver. Also check the side of the tv for HDMI inputs if you have HMDI you can go to Radio Shack and get a converter to go from HDMI into A/V

If you are using Nickel-Metal Hydride, rechargeable batteries, they are not designed to hold a charge for a week---just a couple of days if that. They are meant to be continuously charged or when charged, used immediately; best use for cameras/flash.

They must be selected to be on the same channel. Usually a color code indicates a matched set.

No, finding spares for Headphones is difficult since they are all different, it's not the same as cabinets or speakers. You are better off buying a new pair and keeping your old ones as a spare.

You could try super gluing on another tip or something that is the same size as the original tip and use that as a button.