Maytag Ensignia MAV2757AWW Top Load Washer - Answered Questions & Fixed issues

Your bearings have collapsed

Snubber ring that tub and spin basket assembly sits in is most likely worn. Very inexpensive part but extensive labor involved. I would suggest calling a competent service tech.

What do you mean take out the inside? Do you mean tub? Should have a bolt just under the agitator.

might be a warped spin basket or the dampers could need to be replaced. could even be a bad spin bearing. if it was bearing, normally would be associated with a loud noise during the spin cycle though.

2 screws at base of front panel........remove pull panel towards you slightly and push up to release from retaining clips.

If you are doing the normal procedures and the water elimination function is working, you have power to the circuit board and controls. The circuit board wash cycle section is independent and aligned with the timer circuit, thus the Wash Cycle Controller has failed. All of the functions or options are one the one board and a replacement board needs to be purchased and installed.

Check the wires or problem with the board

there should be agitation..dont know unless its not making the connection in the control head..

If washer hums but doesn't fill, water isn't getting to washer check screens where fill hoses connect to washer. Screens may be blocked. If washer fills then hums check to make sure belt is on. Tip machine up to view belt underneath.

You will need to replace the "water inlet valve". The cold side is not allowing the cold water thru. Here is the part to order.

Where is it leaking water from? Is it running into the tub while in the off position?

The drain hose has to be at least 30 inches above the floor or gravity will drain the machine. Also: If the water hose is jammed into the drain a siphoning affect will occur in some instances. If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Check underneath the machine that the belts are still on and that the motor is turning.

Sounds like the outlet pipe may be blocked or the pump has failed. Sometimes the pump gets a bit of grit in it and stops turning. If the filter is not blocked and the pump makes a noise, switch off machine, blow hard down the outlet hose - this may be sufficient to dislodge the blockage. switch back on and try again - must ensure filter is unblocked first.

You may have to just raise the drain hose up higher. It sounds as if the water is going out the drain hose as it tries to fill.Drain hose should be up as high as the top of the washer.Hope this helps.

Thanks for choosing FixYa. If your washer doesn't drain or spin, you may read and learn what parts may cause this. First, you will want to check your water pump. You need to make sure it is working. Make sure you check the belt on the pump. Make sure it is not broken or loose. Also, make sure your pulley is not stuck in place. Sometimes, they will stick or barely turn at all. If this is the case, you will need to replace it. If the pump, pulley, and belt are working, make sure your motor is working. You should be able to hear it if it is. If it isn't, check your lid switch. The lid switch can cause the motor to not work. It may need adjusted. If not, go ahead and change it. A bad lid switch may cause the washer to not work at all. Now, if your pump is pumping and the washer still won't spin, you will want to check your belt and clutch. Once again, the belt may be broke or loose. Check to make sure your clutch is not worn also. This may be a case of a bad lid switch again as well. You could have a bad drive motor. This is what controls spinning, draining, and agitation. You could have a broken motor coupler. Over time, they will go bad and need replaced. It is possible that your transmission is slipping or damaged. And lastly, you could have a bad basket drive ir spin bearing. This is what allows the inner tub to move. If this is the case, you will probably hear loud sounds or loud banging. I want to thank you for reading and I hope this helps you. Best regards and thanks for reading

What you need is a agitator repair kit, cheap and and easy fix.

Your belt is slipping ,you need a new belt. get model no. and go to your nearest appliance parts store and get another ,easy

Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning


heatman101

The lid switch may be defective. If it is, the washing machine doesn't spin. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washing machine to get to the switch. If it's defective, you need to replace it.Replace the "lid switch" with this part.