Canon PIXMA MP600 all-In-One InkJet Printer - Answered Questions & Fixed issues

6000 is a paper jam or jammed sensor.

http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_mp_series/pixma_mp600#ServiceAndSupport
Click service and support, then enter error 6000, then click Error LCD ... 6000..., then click Removing paper jams mp600. Sorry, but they use javascript so I can't give you a more direct link.

According to the quick setup manual, this printer supports only bluetooth. In other words it is not a wifi printer. In order for you to be able to print on it with a wifi device like a tablet, you will need first to connect your printer with a usb cable to a computer that is connected to your wireless network and then you will need to share the printer on the local network. During the installation process to the connected computer, you should be asked wether you want to share it or not with the network. Simply answer "yes"

The U043 error code indicates that an ink tank is not installed. One or more ink tank icons on the LCD should also be lit up. The lit up icon indicates the applicable ink tank. Verify these tanks are indeed fully seated in the print head and that they are lit up red.

You can also press the OK button to clear this message and continue.

pull out your ink carg and on your printer and then put back the cag and use your printer its work aone

Hi Whitey621
Error code 5100 Try
Solution 1:
Look inside for a tiny object like a piece of paper, a staple...

Solution 2:
There is a thin plastic strip running across the width in front of and below the drive belt: there are fine black vertical lines on this strip. If the strip gets a piece of crud on it, you get an error during the start-up sequence.
Gently clean this strip with a damp lint-free tissue
Hope It Helps: Pineworks.

Kindly remove the printer from add or remove place and then re install the printer from 0 it will start work and kindly remove the old printers from your computers which are no more available to you.

The manufacturers removed the option long time ago due to the printheads and muzzles which get screwed up while printing with one or more empty cartridges. here are some explanations and tutorials on how to actually print with an empty cartridge: How to print without black ink

Solution available on this fixya topic:

/support/t1579890-ink_cartridge_being_rejected

Hi, Be sure to check the printer settings to make sure the wifi option is selected on the printer itself. Once wifi is turned on reboot your computer. It should find it then. Check back if that doesn't solve it and together we can continue the troubleshooting.

Hi Peter.

1. Turn off the machine and unplug the power cord from power supply
2. Plug the machine back in and turn the power on NOTE- If you disconnect the power plug, all the faxes stored in the machine's memory will be deleted

If the error message is still showing, then it is necessary to deliver or send the printer to an authorised repair centre. I am assuming it has run out of warranty, so any repairs will cost you. You can find the details of your nearest repair centre using this link interactive repair centre locator. Also It may be worth checking the roller bar and rollers to ensure they are running at the same speed when flipping the paper over. Regards David

Here is a good service manual: https://issuu.com/timopeltonen/docs/canon_mp600_service_manual

Unplug the printer. Restore power. Hold down the power button for an unreasonably long time until it boots into maintenance mode. Follow the prompts. If nothing comes up call Canon.

Your printer may not have the ability to recognize the files you have in the stick. Did you ever think of that?

You have to make sure the ip address is correct on modem and computer port If you need further help, I’m available over the phone at https://www.6ya.com/expert/alex_22751bbefa74c3d0

Try a hard reset followed by uninstalling and reinstalling the printer software

Hi. Probably the problem is the print head .

No you can not.

Description

Reseat the Print Head to resolve the U051 / U052 error.

Solution

Errors displayed on the printer's LCD screen:

• U051 Print head is not installed. Install the print head.
• U052 The type of print head is incorrect. Install the correct print head.

Reseat the Print Head:

1. Make sure that the power is turned on, and open the Paper Output Tray gently
2. Lift the Scanning Unit (Cover), then hold it open with the Scanning Unit Support (A). (The print head will move to the replacement position.)
3. Remove all the Ink Tanks in the following manner.
   1. Push the tab (B) and lift the ink tank to remove.
   2. Do not touch the Print Head Lock Lever (C) while removing the ink tanks.
4. Once the ink tanks have been removed, raise the print head lock lever.
5. Tilt the print head slightly towards the front of the machine and lift out gently. Caution: Do not touch the print head nozzles <1> , electrical contacts <2>, or ink supply ports <3>. Doing so may cause printing problems. *Before proceeding to next step, check the carriage area for packing material, torn paper, etc. and remove if found
6. Tilt the Print Head and set it in place. Lower the Print Head Lock Lever (E) completely.
7. Insert ink tanks into the print head.
   1. Insert the front end of ink tank into the Print Head at a slant. Make sure that the position of the ink tank matches the label.
   2. Press the mark (Push) on the ink tank until the ink tank snaps firmly into place. Make sure that the ink lamp lights up red.
8. Lift the Scanning Unit (Cover) slightly to set the Scanning Unit Support back to its original position, and gently close the Scanning Unit (Cover). Caution: When closing the scanning unit (printer cover), be careful not to jam fingers. Note: When the next printing begins, the print head cleaning will begin automatically.

If you have reseated the ink tanks and print head and the error still appears, our industry-leading support team is available to help you Monday through Friday from 10 AM to 10PM EST. You can contact our technical support experts by phone or email: Call 1-800-OK-CANON (1-800-652-2666)

Hi! As a first course of action, please unplug the printer from power source and long press the power button for like 10secs. Plug the printer from power source then press the power button and see what happens. If no luck, you may need to update the printer's firmware by downloading from the web. Just type your printer model and add firmware. Hope this helps and have a good one!

reset canon MP280 error