20 Most Recent Whirlpool Gold Duet GHW9400P 3.8 Cu. Ft. Front-Loading Washer - Page 6 Questions & Answers

http://www.fixya.com/support/r3574284-checking_the_drain_pump_on_a_front_loade

Courtesy jsrock16

http://www.fixya.com/support/r3574284-checking_the_drain_pump_on_a_front_loade

Courtesy jsrock516, fixya

http://www.fixya.com/support/t5006688-control_panel_red_light_control_locked

http://www.fixya.com/support/r3574284-checking_the_drain_pump_on_a_front_loade

Courtesy jsrock516

Hi,
There can be many reasons why your dryer will not turn...

This tip that I wrote will help you to figure out what is happening...

Dryer Repair - The Dryer is not Turning
http://www.fixya.com/support/r4422207-dryer_repair_dryer_not_turning

Dryer Repair ? The dryer will not start
http://www.fixya.com/support/r4460438-dryer_repair_dryer_will_not_start


heatman101

Hi,
May be inlet valve be defective kindly replace the inlet valve even if you find that same problem exist the problem with the motherboard of the washing machine kindly give to expert to do the service

make sure its level first

The DL code is door lock. The manufacture explanation of the code is here then my comments follow.

A Door Lock Error occurs if the door cannot be locked. It
will try to lock it six times before displaying the error code.

Possible Causes / Procedure
■ Door lock mechanism is broken or removed from door.
■ Door switch/lock unit failure.
1. Unplug washer or disconnect power.
2. Check door switch/lock unit.
3. Check the wire harness connections to the door switch/
lock unit and Central Control Unit (CCU).

Phil's comments------>

It it almost always a failure of the door latch mechanism. The part number is 8182634 and cost around $45.00

Here is a parts break down to show you where the component is located it is part #7 in this drawing. Sorry about all the trouble you are having, it is usually a good machine and I have one at home myself.

http://www.searspartsdirect.com/partsdirect/showSubComp.pd?imageUrl=http%3a%2f%2fc.searspartsdirect.com%2flis_png%2fPLDM%2fW0111040-00002.png

Try unplugging the unit from the wall for a few seconds, then plug in. If still locked, contact an appliance service company. You may have an issue with the door lock mechanism.

The problem is the coils are failing. They tend to fail as they heat up and eventually just quit. They are inexpensive and easy to replace. It could also be several other things thermal fuse, thermal cut out, hi limit thermostat, heat sensor,or igniter. All of these parts are inexpensive and easy to test and replace.There is a video at www.appliancehelponline.com/servicemanual.html this will walk you thru the troubleshooting of these components. It may be a different model but the troubleshooting will be the same.You can also enter your model # for diagrams and illustrations. Not all models are available. If you need help disassembling your machine there are videos of this also for most styles.

Hi


Thanks for using FixYa. Press and hold the END OF CYCLE SIGNAL button for more than 5 seconds.

Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Drain solinoid valve circuit or vale to be checked.

Dear jodyheidi,
Welcome to fixya.com
I'm Huuum and happy to assist you,


Try this first and if it fails to remedy the problem then call service as you wanted!

Huuum At your service!

With an error code.
This can reset the system.
First unplug the washer and wait a 5 minutes then restart it.
If you can't reach the plug, use the breaker to cut the power for 5 minutes.

It's like rebooting your computer when its acting strange!
Usually it corrects some error problems if they are not serious.
Or they are sometimes just a glitch.
let me know how it works out.

How old is the appliance?

Let me know how you progress!
Bless You, Huuum
Please remember to leave a rating when you are finished!
Thank You

Is the pilot light or "stricker" working when you start the unit.. Is it getting good supply of gas?

yes buy extra hose and connector it will do no harm

No problem adding the extra hose as long as you don't cause the water path to be more work than the pump can furnish, i.e., don't let the hose's height exceed its original height.

The Control Lock is a safety feature that allows the consumer to lock the control panel to prevent small children from manipulating the controls and accidentally starting the appliance. It can inadvertently be set following a power outage, or by leaning against the control panel and usually is not an indication of a washer malfunction.

If this is a Maytag Epic, Whirlpool Duet, or Kenmore Elite, the following link explains how to lock/unlock this feature:

http://www.fixya.com/support/r3608801-control_panel_lock


These instructions are also printed on the front panel of the appliance and in the owner's manual. If this does not correct your problem, then you may have a more serious problem than a simple operator control issue. If you need further assistance, please let me know. I hope this corrects the problem for you.

NOTE: If you cannot locate your owner's manual, you can download or print a FREE copy at managemylife.com. Just type in your model number under the "Manuals" link and you will find your manual listed in a .pdf (Adobe) format.

operator error LOL.

check ur pump