Top 20
Whirlpool AWM8163 Front Load Washer Questions & Answers
Not spinning
if everything else works its probably the circuit board. expensive to replace.
11/11/2013 7:59:32 PM •
Whirlpool...
•
39 views • 0 helpful votes
Awm 8023, the "tumbler" doesn't produce any heat but is spinning ok. Is there any fuse etc that could be bad?
The possible fault could be due to the failure of the heating coil, failure of the control panel or the output drive to the heating coil or it can be one of a loose connection joint of the wiring to the heating coil. You need to recheck the selected program and then check the wiring to the coil. It is important to understand the working of a continuity tester to check the line and the coil which should address the fault. If there is no output from the board then it might be fault of the drive output or the loss of output from the processor which might need tracing of the voltage to the heating coil output. .
6/3/2013 8:04:24 AM •
Whirlpool...
•
43 views • 0 helpful votes
F H is displaying
No water detected entering machine or Pressure switch trip not detected.If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
OrIf the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.
Press PAUSE/CANCEL twice to clear the display.
- If there is no water in the unit:1. Make sure that both valves at the water source(s) are turned on all the way.2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3. Verify inlet valve operation
- If there is water in the unit:1. Verify Drain pump operation2. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch
- Verify there is not a siphon problem
- Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)
- Check all hoses for possible leaks
1/20/2013 3:34:57 PM •
Whirlpool...
•
248 views • 1 helpful votes
Error code 21?
F21 is a Long Drain error.
If the drain time exceeds 8 minutes this error code will be displayed.
In addition, a ?SUDS? error may also be displayed.
This may be an indication of a drain pump problem and/or clog in the drain line.
You will need to check the following:
- First, attempt to unplug the washer for at LEAST 30 minutes to reset the Central Control Unit (CCU). Sometimes this is all that is required to correct momentary glitches with the unit. If the error code returns, proceed to step 2.
- Check the drain hose to make sure it is not kinked or clogged.
- Check the electrical connections to the pump and ensure the pump is running.
- Remove the drain pump filter and check for foreign objects and/or debris.
To check the drain pump, click on the following link for step-by-step instructions:
checking_drain_pump_kenmore_elite_front
If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump.
Hope helps.
5/23/2011 1:51:35 AM •
Whirlpool...
•
48 views • 0 helpful votes
Fault code 08 occurs about 2 minutes in to the
08 ERROR means it's out of balance.This is usually caused by the bearings going letting it move around to much causing the 08 error to show.It's a big job & you would be looking at about 400 dollars to repair.(this is a very common problem with all front loaders)
2/28/2011 8:12:24 AM •
Whirlpool...
•
189 views • 0 helpful votes
Error code FH on my AWM, what does it mean?
Hi,
"FH" is a No Water Detect error.It is an indication that you either have no water coming into the washer, or very little water at all. Check whether the water taps are turned on sufficiently, the inlet hoses are not kinked, the water inlet valve is not clogged, you don't have a siphoning issue, and/or the drain pump is working.
Thank you !!
7/12/2010 7:13:15 AM •
Whirlpool...
•
1,277 views • 1 helpful votes
The digital display read F 7 - will not wash
Hi,
"F07" indicates a Motor Control Unit Error.This error code appears when the Central Control Unit has detected a short in the motor control unit. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. You have to check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU).
Thank you !!
6/28/2010 10:05:03 AM •
Whirlpool...
•
803 views • 5 helpful votes
F11 error
The F11 fault is the motor. I have had this issue myself and found that replacing the contact brushes solved this. The brushes on most electric motors are made from carbon, and wear down with use. They are spring loaded but have a limited life span. These are also cheap to purchase.
1/23/2010 4:00:26 PM •
Whirlpool...
•
376 views • 0 helpful votes
Clean the pump
If there is a kick plate on the bottom front you take screws off and you can get right to the pump, un hook hose and clen out. Now if there isn't a kick plate then you have to go through the back and then do the same.. Remember to unplug unit before entry.
1/11/2010 11:19:46 PM •
Whirlpool...
•
289 views • 0 helpful votes
The code is F09 or
try pushing the pause/cancel button twice to clear the display. you may have a foreign object in the pump.
10/25/2009 1:35:45 AM •
Whirlpool...
•
626 views • 2 helpful votes
WHIRLPOOL WASHING MACHINE AWO/D 5716 - CANNOT LOCATE PUMP
Remove the bottom casing covering the front of the machine just above the floor. Unscrew the circular cap SLOWLY- beware of vast amounts of water escaping though!
I had to use a low height roasting pan to catch water, and just unscrew the cap enough so as to control the flow of water, and enable to empty water away until its all gone. Incidentally, an old hairgrip was found to be the cause of my problem.
Confusingly, "clean pump" meant clean filter!
5/19/2009 1:10:23 PM •
Whirlpool...
•
2,265 views • 12 helpful votes
Washing machines door open light is on, but door is shut
Found it for myself - F7=motor fault. New motor brushes fixed it. This error code will come up if the motor fails to turn on demand at any point in a program, be it filling, in a wash cycle, or spinning.
Hope That Helped;
Thanks For Using
FixYa.com
George
Please Rate Me
5/23/2009 7:27:00 PM •
Whirlpool...
•
553 views • 2 helpful votes
Not finding what you are looking for?